I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
The following ticket explains when I configure pin21 as RESET it will be hardware configured to pull-up internally. https://devzone.nordicsemi.com/f/nordic-q-a/8342/nrf52832...
Hi all,s
I have a couple of nrf52840 boards and i was testing the ble mesh light application. The application works fine, but i changed it so it will periodically set...
Hi, I have tested thingy52-mesh-provisioning-demo in NordicPlaygound on github. It works fine by using a precompiled hex file (via nRFgo Studio) but It doesn't work (light...
Hi, I'm working on enumerating the 52840PDK as a CDC ACM device and I'm running into an issue where it's fully enumerating 80% of the time.
After doing some checking I've...
I'm working with TI's TAS2555 DAC as an audio output driven by the NRF52 via I2S. This DAC requires that the I2S clocks (MCK, SCK, and LRCK) are enabled prior to any data...
I understand that the next version of the mesh SDK will have the GATT proxy implemented. Even after reading the mesh profile specification the following is unclear:
- Is...
Hi,
our product is small tag, size of 70x35mm2.
Plastic covers are welded together and now looks like after welding some HW does not work properly. Flashing is successful...
Hello, I am running ble_app_uart_c example on nrf52832 IC. It is connecting to its corresponding peripheral and I achieved bidirectional communication.
The problem is,...
Hi! I am using SDK15 to develop an application for nordic chip which won't be using any kind of display nor keyboard input, so probably I'm gonna go for static passkey option...
I have and older board which is the PCA10028 with the nRF51422 chip.
I have downloaded the nRF5 SKD 15.0.0 and found there is not example DFU project for my particular board...
Hello
I am working on a project based on the Mesh SDK 2.0.1 light_switch example. The system is using SD 6.0.0 and PCA10040 boards. DFU is successfully implemented on the...
Hi,
I work on nrf52832 with the serialization.
The nrf52832 connectivity part is load with S132 V6.0.0 (uart hci).
The stm32 will communicate with the 52832 throught...
Hello, can you say me:
1) which Stack parts in Mesh SDK: nrf5_SDK_for_Mesh_v2.0.1 are implemented in harmony with Bluetooth Mesh Profile Specification and which are not...
Hi,
We are attempting to send data via BLE every 100 ms using an app_timer. The app_timer sets a flag and in the while loop in main.c we call
ret_code_t err_code; do ...
Hello, i'm currently doing my own DFU central for the BLE DFU on SDK 13, i followed all the steps on this link , i created the init and image files with nrfutil and now i...
