Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi,
I have a beacon code for nrf51 that I wanted to port to nrf52. It uses app_timer, gpiote and adc. The power consumption in idle is ~30uA. Now I wanted to port this code...
FDS_VIRTUAL_PAGE_SIZE
The size of a virtual flash page.
Expressed in number of 4-byte words. By default, a virtual page is the same size as a physical page....
Hello,
I would like to use proxy_server(example of light_switch ) and ble_app_blinky_c, to make these two functions work together in one card. So this card can be controlled...
Hello everybody,
i have crated an Report id for the telephony usage on iOS from here https://opensource.apple.com/source/IOHIDFamily/IOHIDFamily-247/IOHIDFamily/IOHIDUsageTables...
Hello All,
I'm trying to program a NRF51822 module for the first time.Using Keil, Soft device s110_nrf51_8.0.0,soft device kit nRF51_SDK_9.0.0_2e23562 when I try to program...
I found the next response in a topic and i would like to know if there are some new improvements in the last SDK mesh 2.01.
devzone.nordicsemi.com/.../120547
I turn off...
I have installed from "nrfgostudio_win-64_1.21.2_installer" on Win-10 laptop. Weh I start nRFgoStudio, the main window appears for a second then I get a message "nrfgostudio...
Hi all, we're using code from this forum to enable GPIOTE and PPI to measure the low between the arrows to indicate a "start of transmission" and then switch to measuring...
Materiel and software use :
SDK mesh 2.0.0
SDK 15.0.0
NRF52832 with PCA10040 x5
Situation :
I would like to implement this network :
I follow the instruction...
I'm using the UARTE peripheral via the UART driver code in SDK v14.2. Due to transfer size and SoftDevice timing I have to use the double-buffered receive method (by calling...
Hello,
I am trying to make a beacon start advertising on a long press of a button. Using this as a reference, I implemented a timer as follows:
this is the flag to keep...
Hi!
I am using SDK15, my application is based on app_ble_uart. I have added my proprietary characteristic to NUS next to RX and TX Characteristic with quite a success. Now...
I use sdk14.2 nrf52832 as the primary, connect two iphone peripherals, iphone is connected to broadcast, when I turn on both peripherals, sometimes everything is normal, sometimes...
Hi
I am a beginner to BLE based products, i bought the nRF51822 devices hoping to create a mesh network. The problem is i have got the development boards but i am not able...
Hi there,
I'm new to Android BLE development and simply trying to read out a BLE temperature sensor that encodes the temp. in the service data from the advertising packets...
