I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi,
I found some sensor drivers under nRF5_SDK_15.0.0_a53641a\components\drivers_ext\, like hts221, lps22hb and so on.
Where can I find example for those driver?
Regards...
Can someone please clarify a few things!
I'm trying to get high bandwidth on some to and from phone transfers. I have control and data gatt boxes, control has the connection...
Hi,
i am doing a project where i have to discover multiple custom services on connected ble peripheral from ble central device.
i am using nrf52832 with sdk 14.2.0 as...
hello,
Now i have two troubles in NRF52832 Gateway.
1.Planning introduce：
The only function of NRF52832 Gateway is to scan beacons' advertisements. With beacons‘ number...
Hello all,
So I've ran into an unfortunate situation, our firmware team decided to ditch us just as we're about to launch our product. I got a dump from them including...
HI,All
Before I erase flash ,I must do memcpy(). I do not know why.
As follow, after i delete the function memcpy( (uint8_t*)&data_buff[0], pdata, len), when i write data...
I have been trying to execute a simple program for GPIOTE event. I am using SDK 15.0 and using the nrfx_gpiote li"brary. I have added the required headers.
Yet, I am getting...
Hello,
I have a product in the field (sdk 12.2 and soft device S132, based on NUS profile) since a couple of month that works ok but crash with some Samsung devices
...
Hi I am trying to write a driver for the nrf8001 BLE and interface it with LPC1758 Arm M3. I am a beginner in this field and I am not exactly sure, if I am following the correct...
I try to port LESC example from PCA10040 to PCA10040e(52810) on SES.
Porting work has been done. When building, it reports VFP issues of liboberon_2.0.4.a, as below:
...
Hello all,
I am using the latest SDK 15 and softdevice v5 (downgraded from v6 thought it was causing issues) on the NRF52 DK. When I build my application it states:
Compiling...
I want to make my device automatically go to sleep mode when the power is connected. And when the device wakes up from sleep mode, it should not automatically go to sleep...
Hello, We are trying to use the debugger tool on Keil for the nRF51 DK, But we are having a really hard time to figure out how to make it work. Do you guys have a tutorial...
Hi,
I am developing my own program based on serial example. Project is based on gcc compiler under eclipse. I have preapared my own board with rigado module (nrf52832). HW...
