I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi All!
I must to add some binary data to ADV packet use Manufacturer Specific field.
I fill the related fields:
static uint16_t adc0_data = 0; // ADC measured data...
Hello,
Is there some exemple about how to secure a NUS connection between two nRF5x (one NUS, one NUS_C) ? Dans it use a preshared passkey ? Is that secured (man in the...
Hello,
I am migrating a working application from SDK13 / nrF52832 => SDK14 / nRF52840 and during build, i get undefined reference for sqrt, sin and cos functions.
I...
hi
I mistakenly left the inductor connected between the dcc pin and the DEC 4 pin and let it operate in the LDO mode.
What kind of problem will you encounter?
Or maybe...
hi all, I want to learn about HCI layer . It has 4 packet and I dont understand about HCI ACL data packet and HCI synchronous data packet . how are they diffent? Packet from...
-Dear Nordic Devteam
Thanks for your endeavor for the nRF Sniffer 2 . Although it is a beta version, this is sincerely anticipating.
To set up the Sniffer you will...
I am developing some firmware using SDK 8.1 where power consumption is absolutely critical. The firmware will make a ble connection between the central and peripheral device...
I'm facing a strange problem that I don't really understand:
I'm using 51822 (s130) on a custom board to communicate with iPhone 5S. The parameter that is able to establish...
In multi-link central app, after BLE_GAP_EVT_CONNECTED event, BLE_LBS_C_EVT_DISCOVERY_COMPLETE is called NRF_SDH_BLE_CENTRAL_LINK_COUNT number of times.
So For example...
Hi,
I use the original "nRF5_SDK_14.2\examples\ble_peripheral\ble_app_uart" no any modification, in Keil the .hex file size is 71k while it is 153k in SES.
My questions...
I am working on SDK V10.0.0 because I need S310 softdevice.
I like SEGGER_RTT I used in SDK V11 and V12.
But I got the Error in the subject line.
I had to uncheck use_microlib...
Hi,
I build below sample in SES and receive an error for:
Compiling ‘nrf_log_backend_serial.c’
can't open '...nRF5_SDK_14.2.0_17b948a/examples/ble_central_and_peripheral...
Hi!
There are many questions about flash memory already.
But I could not find the question I wanted.
I want to save scan data to flash memory.
However, when you...
