Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Looking up to Nordic guys for solution to
Play music from mobile to the connected BLE Slave device which has speaker connected.
Stream audio or play music/mp3 from...
In the file bsp.c (from the SDK11 ble_hrs example) I don't quite understand the initialization statement:
static bsp_button_event_cfg_t m_events_list[BUTTONS_NUMBER] =...
Hi,
I'm working with UARTE using a receipt timeout. So far so good, I tweaker nrf_drv_uart to get notified upon RXDRDY interrupt (char received but not yet DMA transfered...
Hi,
I've got some software that already uses nordic_uart, so when I try to add another uuid I get NRF_ERROR_NO_MEM.
Now reading around at others with this problem, it...
Dear Nordic,
I am following this test example [https://github.com/NordicSemiconductor/nrf51-ble-app-lbs/tree/throughput-test-5.2.0] while using nrf51822 dev board.
I...
Hello.
I use nRF52 , PCA10040 , S132 , SDK 11 & Keil5.
I want nrf to do bit operation.
The code about bit operation is following.
unsigned char tmp[2];
unsigned short...
Dear Nordic Team,
Thanks for support.
I try to enable dfu service in proximitty example code as per the nordic document .
But its not work. I dont know what i am doing...
To the wizards at Nordic,
I come to you with a rather perplexing issue, we are building a custom application on top of our nrf52 based design. The board seems to work great...
I think similar issues have been posted before and not resolved
If I flash the hex precompiled hex files for virtually any project by using the pca10028 S130 version it...
Hi, I want to detect long and short press in same button. Define "BUTTON_DETECTION_DELAY" can detect one delay. Let me know to detect more than two delays.
The same question...
hi,
i am working on blinky example code. i was build the code and generated hex file using Eclipse IDE. i have nrf51822 ble module.
want to flash the hex file using dfu...
Most of the make files and project files within the nrf5 SDK contain a bunch of defines of the form -DNRF_PAN_XX. A search through the SDK v11.0.0 reveals only a few references...
I have included all paths of all (.h) files including (nrf_delay.h) however I got errors as seen in the photo. What do you suggest to overcome such errors?
Also, Is the following...
Hi,
This is very newbie, and I am stuck.
I am following to the letter the instructions to create the micro-ecc according to this instructions.
The problem, and it...
