Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
I am having an issue with running the initial blinky example that came with the nRF51 PCA10028 SDK in the Eclipse IDE . I will include screenshots of the issue. I believe...
I use nRF51-DK and nRF51-Dongle for a BLE sniffer.
Always the sniffer fails and marked with an error "Encrypted packet decrypted incorrectly (bad MIC)".
It can not be...
I've tried a trivial example (blinky-like, compiled by gcc using proper startup and ld scripts) on nRF52 devkit, but I always only get hard fault.
Debugging through the reset...
The nRF24L01 dataseet V2 (the most recent I think?) states (p.23) that the nRF24L01 can operate on frequencies from 2.400GHz to 2.525GHz . The channel steps are stated as...
I am completely confused by the nRF51 UART. I'm trying to port code originally written for an STM32 (another cortex chip). There, I define an interrupt, enable the RXRDY or...
Hi,
I need to have two different interrupt handler for one pin?
For LOTOHI one handler and for HITOLO another handler, how to do that?
Here is what i did until now...
Hello Nordic and fellow developers
While implementing bonding into an application based on S130 I found it necessary to test on the role of a given connection. Different...
I am getting device id of peripheral on central and then getting it displayed on hypertermianl hyperterminal using ble app multilink perihperal code with multilink central...
Hi Everyone,
I have what I hope is a simple questions. I am creating a piece of hardware that will act as the peripheral to a central iOS app in regards to a standard BLE...
Is there any construction available in the SDK, to achieve printing functions, with an undefined number of parameters ? The classic example :
#ifdef CONFIG_DEBUG
#define...
Hello,
I've ready the final S130 spefication and it states that the advertiser is started as early as possible and that i runs asynchronously to all other roles. Now I...
Calling app_sched_event_put() from the NRF_RADIO_CALLBACK_SIGNAL_TYPE_START signal handler causes a crash due to the CRITICAL_REGION_ENTER() call inside of app_sched_event_put...
is there any code for device which act as master and peripheral other than nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental \app_s130_demo\pca10028...
I have a simple nRF51822 BLE application where a voltage is read by ADC periodically, and several values are sampled and averaged. However, from time to time, I get another...
Hello All ,
I am working on nrf51822 with sdk 7.1.0 and softdevice 7.1.0 .Earlier my ble connection was working very good with no disconnection anytime unless i disconnect...
Now I'm working with MCP 3.9.0.
When any device is connected, characteristic default values are not 0's. Can they be initialized in any way? It is a little bit annoying when...
