Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
I'm using
s110_7.1
sdk 7.2
DFU
updating application (application.hex + application.dat zipped) works fine, but when updating bootloader (bootloader.hex+bootloader...
Hi,Nordic support
Circuit design: Unused I/O pins
where can i found recommended I/O end terminal desing of unusing GPIO pins ?
I'd need such as pull-down resistor......
HI, I'm extremely new about Nordic component and device.
I buy a nRF51 DK for start understand hou BLE work, I attach to my pc, the green led power on and my pc know the...
With S110 v8.0.0's size increased to 96K, I'm concerned that my current memory layout is going to prevent me from upgrading to a future softdevice.
It seems that the only...
The function dfu_ble_get_peer_data seems to be declared in dfu_ble_svc_internal.h
but not defined, (not actually implemented) somewhere deep within the Nordic Software Packs...
Folks,
Simple UART communication shouldn't be this difficult. Embarrassed to admit it, but I'm having problems setting up and using the app_uart.c/.h module from the SDK...
Hi all,
I have a working prototype of a service which enables a number of characteristics for the control of motors and relays. The motors work great, and are controlled...
Is it possible for gpiote_event_handler interrupt to get executed while the program is executing code inside timer_event_handler?
These events modify same variables so...
I intend to keep a long running clock in the system and use the app_timers(hence RTC1) in a soft device enabled nrf51822 firmware.
I basically have a minute tick and update...
Hi,
I want to run the experimental_ble_app_uart application on our custom nRF51822 board.
However, I could not find a proper bootloader to start the application. Is...
Where can I find an example of using device manager? The SDK doesn't have anything. I am using S110 7.1.0 and SDK 6.1.0 on nrf51822. I am having lots of problems with iOS...
I try to use Android studio to build nRF Beacon project,but it didn't work ,and there are several error .
the error is
Error:(50, 35) No resource found that matches...
Hallo,
I try to use the s310 timeslot API. I open a "session" and then request a timeslot:
check( sd_radio_session_open( nrf_radio_signal_callback ) );
request_radio_slot...
I am trying to implement the pulse counting mentioned in a previous post of the same name, but the code is eluding me. I am using the heart rate service example with new code...
Hello,
I want to implement a firmware update over ble for my application and the SoftDevice 130. Which would be the correct boatloader.hex that I should use? I am working...
