Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hi , I succeed to flash the firmware to Thingy52
you can see the attached 2 pictures one is for the nRF Mesh app and the second is the Thingy 52 (Four units) which are ...
Hello,
I am using nRF52840 DevKit, SDK 16.0.0 and SoftDevice 113 v701
I am looking at nrf_bootloader example and want to configure a watchdog that keeps running even...
Hi,
I'm wondering what is a good way of keeping track of when the device is inside the active time window so that the data is being sent at the correct time.
Here is my...
Hi,
I'm working on two projects, in the first one, nRF52832 (softdevice S132 V6.1.0) is used as a slave component communicated with STM32L4+ over UART and the second one...
Hello,
I have been using nRF52840-DK and also nRF52840 Dongle for testing and I found an interesting behaviour when I established my test setup. The RF module acts as an...
Hi All,
We have a product based on nrf52832 that has a custom ble service with 2 custom characteristics.The first one is to send data to the nrf device and the second one...
Hi
I opened the Watchdog in the user application,and do nothing in the bootloader.Then when I use DFU,the CPU reset appears.How can I to deal with it?
And when I upgrade...
Hi
I am looking for some specific contract developer help to build and Android app to update Firmware in devices using DFU and the buttonless service. Obviously there are...
HI,
We are evaluation the nRF9160 in the devkit and we are trying to obtain the values specified in the nRF9160 Product Specefication v 1.1. After following the different...
Hello,
There are many questions out there on correctly determining the SAADC pin input voltage limits. The equations given in the product spec is very straight forward:...
We are creating and application that will use the Serial port to communicate to a host using an RS485 protocol. We have it working in SDK 15, but we are now trying to build...
Hello All, I want to generate Bi-Phasic two PWMs with 180 degree interphase delay and variable Duty Cycle with variable frequency upto 250 Hz in nRF52810 SoC. Can you please...
Hello, how can I use the functions in nrfx_twim.c
Using SES and the CMSIS config wizard, I have picked:
NRFX_TWIM_ENABLED 1
NRFX_TWIM0_ENABLED 1
NRFX_TWIS_ENABLED...
Hello
I wonder how to verify that teh scan response data is set correctly and if there are other parameters I need to set to get it working.
So for setting length i have...
