Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
I want to connect and get data multiple peripheral to a single central device.
I used this example https://github.com/NordicPlayground/nrf52-ble-app-uart-c-multilink
...
I can't figure out how to respond to a custom Zigbee cluster command, let alone send a custom response. Is there any example on which I could understand how to send a command...
Hi!
we're just finishing the layout for a custom nRF52832 board. On the custom board we have a connector for SWDIO and SWCLK to flash the firmware. Can we use theese 2 pins...
Hi,
I'm trying to familiarise myself with the available crypto functionality on the 52811 and have managed to get basic AES-128 block encryption working using the ECB peripheral...
Hi,
I am using pc-ble-driver-4.1.1 to receive BLE peripheral Device 240 Bytes notifications. And I used "pc-ble-driver-4.1.1\examples\heart_rate_collector" as starting point...
Hi Nordic team,
we want to connect 2 nRF52840 based modules with Coded Phy S=8 Mode to make an cable replacement (NUS). MTU Size is 244 Byte ,to transmit cyclic 200 Byte...
I am trying to connect the DK to AWS.
I got the AT example working and uploaded the certificates. I managed to update the prj.conf file (and then took quite some time to...
It continue to give "No device available" when I connected thingy 91 to the nerf connect programmer app. I tried turning on device while keeping SW3 pushed but still not detected...
Hi Team,
We are planning use the crypto libraries for our application, just we want to know which library is best for us in terms of speed and memory consumption,
1. mbed...
Hi, I'm almost finished setting up a development environment for nRF52840 DK on macOS. I used the new Toolchain Manager to install everything, and then imported the "peripheral...
While developing our project using NRF9160 , we encounters a hard fault. The screen shot and the map file is attached. Please help us in understanding what is happening from...
Hi, we are using nRF52832 SAADC in differential mode. We have two channels connected.
Inputs are now configured as differential-N and differential-P (PSELP and PSELN). ...
Dear all:
i have a problem about connect distance. My central device is nRF52840 ，peripherals are nRF52810 device。all device Hardware RF performance are good. But,when my...
Hi In continue to Tzvi Kaplan thread and other threads here related to the PDM, like this one:
devzone.nordicsemi.com/.../single-pdm-microphone-at-higher-pcm-sampling-rate...
