Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Dear everyone,
My platform is SDK16 and IDE is KEIL V5.25.
I set timer 2 to 104uS to sample a serial data. It isn't UART data, no start bit and stop bit.The start bytes...
1. Using the nRF Connect SDK v1.2.0 development environment, nrf9160 developer, when testing connections to NRF_CLOUD in China, cannot be connected. 2. Please provide the...
1. Optimization is set to 0 flash read and write errors, set to 3 flash read and write correctly? 2. Please tell me what effect the optimization is on flash reading and writing...
Hi .
I am using nRF52840 dk in windows 10 environment.
I want to measure the RF output power of a single nRF52840 using nRF52840 dk.
I succeeded in generating a...
Hello,
On my custom board, on nrf52832, I can can use app_buttons for all usual pins, but not the XL1 (P0.00). I didn't try XL2 (not routed)
Using this pin as input or...
Hello devzone! I am using translation.
I'm trying various things in a continuation of my previous post , but I do have one question.
I set NRF_LOG_ENABLED to 0 at ble_app_blinky...
I've got an nRF52840 dev kit and am building my code using the app_ble_hrs_freertos project as a starting point. I'm building the .elf file, which I load into Ozone to do...
Hello everyone,
I hope that you are all doing well during those hard times...
I am writing a code for a nRF52840. The connection is successfully established with a cycling...
I have the NRF_CCM peripheral setup to encrypt packets on-the-fly. I can verify packets are properly encrypted when the payload size is 27 bytes or smaller. However, anything...
Hi,
I have created a configuration based on usbd_app_uart example where both usbd and softdevice are enabled on my device as soon as the device is turned on. When I transmit...
Hi,
I am developing a simple application that utilizes a light switch client example for NRF52832 with SDK15.0 and Mesh 4.0.
I am facing a problem when using the FDS module...
What could be the reasons that cause DFU Bootloader BLE not working with nRF Connect on PC (while it works with nRF Connect on iOS)? I have had various problem with nRF Connect...
Hello
I am using Seggar Embedded Studio for ARM V3.4 and nRF_SDK 12.3.0. I am trying to understand interrupts and interrupt handlers.
The interrupt request for Watchdog...
Hi I would like to ask you for advice on how to solve my problem with Ble and the timer I have nRf52840 and I am trying to add a timer to examples\ble_peripheral\ble_app_uart...
Hi,
Setup:
I’m sending ble packages with around 80 Hz from an server (nrf52832 sdk 15.2) to a client device ( nrf52840 sdk 15.2)
One Ble package consist of several...
