Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Hello,
I want to use the nRF52832 as native transceiver 2.4GHz and I'm looking at examples of the latest SDK.
I'm using Segger Embedded Studio.
I found some examples...
Hi, I'm on final development stage of my custom board. I'm using nRF52840 with nRF5 SDK v15.0.0 and S140 SoftDevice v6.0.0. I need to trace the over-the-air communication...
I'm not using a softdevice, and am doing some time critical measurements when the radio begins transmitting.
This code works very well with nrf51:
__disable_irq(); NRF_RADIO...
Hello
I have a question i cannot figure out. I'm using my phone to send string on my NUS client (NRF52 with SDK15.3.0 and FreeRTOS) and the event BLE_NUS_EVT_RX_DATA is...
Hi,
I am new to development with Nordic chips. I am using nRF52840-DK (SES,nRF5_SDK_15.3.0_59ac345) to read analog input on ADC pin AIN0. I want to continuously read the...
Hi,
I used a NRF52832 to test our product with Python Script.
I enable my notification. I start to receive notification and I have a crash after received first notification...
I've used the DFU bootloader from SDK 14, s132 and the ble app uart example as a boilerplate for my app.
Now i'm looking into making some relatively large changes to the...
Hi,
I have problem compiling "HTTP application update" sample form the SDK for the NRF9160. I am using all the latest tools: * segger embedded studio: v4.18 * nrf SDK v1...
Hello,
I had problems connecting the periphery to the central. When I connect them, I get notifications like this from peripheral, but after this message they don't lose...
Hi,
We are using nrf52 dev boards running mynewt and until two days ago we could use the app to identify/provision and get composition data for nodes and get composition...
We are in the final throws of testing our boards that are based on the BLE UART Peripheral application. The current test environment involves monitoring board and battery...
i changed the code to send environment data over ble_nus service and it was worked
so i tried to send motion sensor data over ble_nus service and i changed code but no data...
Im developing a mesh network based on a custom board using the nRF52832.
I fine with sending some bytes over mesh . But now i want so send more bytes over mesh using Instaburst...
Hello,
I am using nRF52840, SDK_16.0.0, S140 SoftDevice and Segger 4.16 for flashing the image. I am using ‘ble_app_blinky’.
I have few queries on setting Tx power...
