Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Using nRF5 SDK v15.3.0 Peer Manager drops Service Changed indications if an ATT MTU exchange is in progress, this hapens because function service_changed_cccd() in...
Hi there,
We need help with BLE bootloader.
Here's our setup: nRF5_SDK_15.3.0_59ac345 52840, Production PCB SES compiler for bootloader IAR 7.60 for our production code...
Hello,
I am using nrf52832 SDK 15.3.0, in Segger Studio IDE.
When i am using NRF_LOG_FLUSH in my application , then application is getting stuck in the below code:
...
When the transmitter frequency is 2445MHz and the receiver frequency is 2413MHz, the receiver will receive the data from transmitter correctly. Not only the receiver can receive...
Hi, currently I use nRF Connect v3.0.0 to flash my nrf9160-DK. With the Segger Studio from Nordic I am able to generate the merged.hex but now my problem: I erased the chip...
Hello
I would like to compile Direct Test Mode on Segger embedded Studio.
I follow all instructions with getting started assistant
but i have one error : error 5 cannot...
I am starting with the nRF52-DK. Page 8 of the documentation has links for examples to get started.
4 Start developing After you have set up the development kit and installed...
Hi,
I get the problem when I tried to download ncs
west update WARNING: Can't set ZEPHYR_BASE: parsing of manifest file failed during command update : no "manifest...
Hello, everyone, I have an issue where I could use some help!
I have this setup.
- One nrf52840 ble peripheral (the data collector) that accepts multiple central connections...
Hello all.
I am developing a BT4.2 compliant application. I have a question about LESC (LE Secure Connection).
devzone.nordicsemi.com/.../how-to-implement-ecc-functions...
I am using the custom_bluetooth_service tutorial from https://github.com/bjornspockeli/custom_ble_service_example . I am trying to set the value length of the custom characteristic...
Hi,
I've been trying to connect nRF9160 DK to google cloud by running "google_iot_mqtt" following the directions here https://devzone.nordicsemi.com/nordic/nordic-blog/b...
I use SEGGER step-debug commands F5, F10 and F11.
Sometime F10 cause the debugger to step into disassembly code, making continue debugging hard.
Restart debugging 'cause...
Hi, I have an nRF51822 with s130 doing normal advertising and a Nordic UART service. Is there an example somewhere of doing some simple observation with it at the same time...
