Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
I am having an issue with running the initial blinky example that came with the nRF51 PCA10028 SDK in the Eclipse IDE . I will include screenshots of the issue. I believe...
Hello,
I want to change the TX address or channel "on the fly". Since this did not work for me, I read the following post: "Is it possible to change TX address on nrf24l01...
Hello everybody!
How can i read the temperature, the battery-% or other data from the Thingy when using the Linux console and not the SDK? My steps so far
1. With i was...
I am estudying and modifying the light switch example.
the example shared in the SDK, this example works as star network. (1 client and 3 (or many) servers) where:
- The...
Hi,
I' writing an app based on ble_thread_dynamic_template with added CoAP utils, but with a few changes. Program works fine, I am able to communicate over CoAP, but after...
Hello!
Last time I've described issue with connection problems in large thread network https://devzone.nordicsemi.com/f/nordic-q-a/29867/thread-mesh-network-capacity-problem...
Hi,
I have encountered a 404 error:
<<<
HTTP ERROR: 404
Problem accessing /help/pdf/nwp_017.pdf. Reason:
ProxyServlet: /help/pdf/nwp_017.pdf
Powered by Jetty...
Hi,
I am trying to send stream of data over BLE. I am using nRF52 development kit and in that ble_app_uart code is running. I want to send continuous data to the UART and...
I am using PPK 1.1.0 to compute current draw on a custom hardware.
If I upload ble_app_hrs example on the nRF52-DK and measure it directly, I obtain average reading as 550...
Dear all,
sorry for asking a very beginner's question but I'm really a beginner and want to understand what I'm doing :)
What I have:
nrf52 DK
nrf SDK11.0.0...
Hello,
we are using the USB CDC ACM Example to set up a USB connection between the computer and the nRF-Chip.
By pressing Press Button 1 a bunch of test data will be sent...
Hi!
Is there any programming guide for establishing mesh network? I want to develop from scratch but i can't find any document for programming to mesh network. I seen Light...
Hi
I am able to successfully compile my C++ code on Raspberry Pi3 however while running an executable file. I am getting below error.
pi@raspberrypi:~/RF24/librf24-rpi...
Hello,
I would like to send an int32 value every 500ms and use for this the same procedure as it is shown in the heart-rate-example. The code for sending is:
// Send value...
Hello Nordic Devzone fellowes
I tried DFU with NRF 52 DK board with 'PC-BLE-DRIVER-JS' dfu.js test code
When the firmware .zip file is 128 KB the speed of transftering...
