Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello, I configured nrf52832 as central. I am using ble_app_uart_c example to set the IC as central. And esp32 module is my peripheral.
I am able to establish connection...
I download the mesh sdk from: http://www.nordicsemi.com/eng/nordic/Products/nRF5-SDK-for-Mesh/nRF5-SDK-for-Mesh/62377
Compile the light_switch/server project for nrf51422_s130...
I am working on an nRF51822 central BLE device. I am wondering if it is possible to lower the clock speed / underclock the device to save power? I know this will make it run...
Hi,
Can we test Nrf52 Advertising extension feature with nRF Connect app in mobile?
Do we have any other app whrere we can test this feature using nRF52832 DK?
Does the following SOC,
nRF52840
nRF52832
nRF52810
have sub 1-ghz RF ? by reading it seems that it is having the 2.4 Ghz RF.
I was looking for 433 MHZ or 863...
Hi.
I want my peripheral, an nRF52832, to accept a connection from the first peer it sees and bond with that peer, and thereafter accept connections only from that peer...
Hello
I am using sdk version 14.0 and softdevice S332. I successfully tested on the nrf52832 board using the ant bsc example.
However, when we put the code on our custom...
Good evening,
I am trying to implement queued write (long write) into ble_app_uart example. I am using s110_v7.1, nrf51822(pca10028), can not find version of sdk it is...
I have enabled radio notifications (through sd_nvic_ functions). When sd_ble_gatts_hvx() (notification) is called once, I've noticed two radio active-nactive windows occur...
Hello,
I have a bootloader with a low power wait for power button on startup.
When I do a BLE DFU update of bootloader + SD + appli, the Nordic smartphone application...
hi
I have a application use NRF52832 to scan beacon's advertising and write the advertising data into NRF52832's advertising.
I found the working current is nearly 3mA...
Hello,
I am useing NRF51822-QFAC in my BT bridge project; Now I need to design the matching circuit; there was some recommended matching circuit in the datasheet(11.3--11...
I have a central device that uses BLE to scan for a specific device (there is only a single device it can bond with). Right now it checks the UUID and the mac address of all...
my device giving output as square pulses.but would like to control current from the range 50uA to 500uA of square pulses.how to calculate it. can someone help me
Hi,
I have a question that Product Specification v3.1 of nrf51822 describes Flexible Power Management: 2.6 μA at 3 V ON mode, all blocks IDLE. But, in the same place, NRF52832...
