Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
I need to read the UID and later on also the RSSI value of devices (Handys) in range.
It should be reading the values automatically without the need of manual connecting...
The datasheets for the nRF24LU1P ansd nRF24LO1P have near identical example antenna driver designs which vary in the values for the inductors, etc
The LU1P datasheet is...
Hi,
I've combined twi_sw_master and DFU in my project based on nRF51822 Beacon v1.1.0. Now I can't connect to the beacon. The same project only with DFU or only with twi_sw_master...
Error is shown in the following figure.
I use nrf51822-DK(256k)
The exception of BLE_S110 works well.
Memory Is not enough when you add a BLE_S110
Is there any...
I am using S120 v2 with SDK 6.
Initialization of the softdevice and device manager return no errors.
However when I want to start a scan for devices, the function checks...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
Hi,
I am using Timer0..2 interrupts along with radio TX/RX. When the Timer2 interrupt coincides with RX/TX the Timer2 is halted for approx. 450 µs during TX. Is there a conflict...
hi...
i am working on nordic nrf51822 evaluation board.i coudn't get pin 31 interrupt.but in all other pin i can get interrupt. maximum of 3 gpiote pin events is using...
I'm following the example here for the PCA10028, only the example I copied from the Pack Installer is called ble_app_hrs_s110_dfu_experimental_pca10028 (nRF51 PCA10028) instead...
Hi, I am studying with nRF51822 (s110).
I found some source code from devzone.nordicsemi.com/.../
and I am trying to change the device name,
And I don't know why...
I am trying to integrate BLE into my wireless heart rate monitor project with an Arduino Uno.
Everything works and can successfully be exported over a different BT antenna...
nRF Master Control Panel on LG G2 with Android 4.4.2 can't connect to S130 v0.9 with example that goes with SoftDevice.
But it can connect to S110 example that goes with...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
