I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
I am having an issue with running the initial blinky example that came with the nRF51 PCA10028 SDK in the Eclipse IDE . I will include screenshots of the issue. I believe...
I use nRF51-DK and nRF51-Dongle for a BLE sniffer.
Always the sniffer fails and marked with an error "Encrypted packet decrypted incorrectly (bad MIC)".
It can not be...
Hi,
I'm using long write in one characteristic but if I try to configure this characteritic with write authorization (attr_md.wr_auth = 1) it doesn't work. I need to send...
Hi, I disassembled an Acer Mouse and saw a chip named "NRF A 3152c 1517UH". Can anyone identify the chip or provide me with the data sheet for it.
Regards,
Steve
After i asked this question , i changed to use SDK 8.0.0 hrs "s110_for_dfu",
As the same step to try,
i downloaded softdevice(s110) & bootloader(for 8.0.0)
then opened...
Hello All,
I am trying to create multiple threads for an individual tasks. But when I am creating new thread my program is not working and it's going into some infinite...
Im sending an 8 bit int using my AVR controller as follows:
static uint8_t* dummy_heart_rate = 6;
aci_loop();
if (lib_aci_is_pipe_available(&aci_state, PIPE_UART_OVER_BTLE_UART_TX_TX...
Are there any pins that I can NOT use for SPI on the nRF51822? I'm not seeing any notes in the latest documentation but would like to make extra sure before I spin a board...
Hi there,
Using mbed i have currently programmed an nRF51 DK to transmit data through a custom service with 6 read only characteristics. Is there a simple way i can alter...
Hello.
I cannot get my head around app_timers. After reading the docs, examples and answers on the devzone I'm still unable to get it running. The timeout callback isn...
I am trying to add SPI to the ble_uart_example on my nRF51-DK but when I try to debug my code debugging just stops (All "step one line" etc. buttons grayed out) at this line...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hi,
I'm using nRF51 Development Kit to program the beacons. I've connected the beacon just like it's described in the last update of this thread using the 10-pin adapter...
Hi,
I just noticed that the nrf51822 doesn't have an eeprom and I already had the pcbs done. Can I use the NVMC to write USER data on the CODE (is it flash memory are?...
I am trying to do over-the-air (OTA) device firmware update (DFU) on a device with bootloader same to the "dfu_dual_bank_ble_s110" example in the latest nRF51 SDK . On the...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
We are using Gazell to stream data at <=6mS intervals for very low latency wireless gaming peripherals. We'd like to have many of these peripherals devices (more than 24)...
Hello
I'm trying to get a SPI master onto my S210 programmed nRF51422. I'm using uVision 5 and have all the nordic packs installed and built off of the ant broadcast tx...
main.c
I am trying to talk to this sensor: www.meas-spec.com/.../MS5803-05BA.aspx via SPI... it quite seems to work as I get expected responses to commands but as the title...
Do the Nordic Boards offer some sort of config region where settings like the Bluetooth address are stored? I would like to change these settings without having to recompile...
