Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I am using android ble with kotlin. I ported the Blinky example to kotlin. There is a reference escaped in object construction when on construction the BLEManager invokes...
Dear Nordic Team!
I am verifying my tools chain for nrf52840 Mesh project development by mesh light-switch example. I have 4 PCA10056 and make them to 1 provisioner, 1 client...
Hi,
I use sdk16 and nRF52832.I want to change advertising in the air:
Now I'm using the timer to change the adv.But I want to change adv with RF interrupt.
Like this...
I developed an application (BLE named Adriano) using nRF52840 DK, nRF5_SDK_for_Thread_and_Zigbee_v3.1.0_c7c4730, starting from ble_zigbee_dynamic example. I added some custom...
Hi,
I'm developping an application for nRF52840 as a BLE central. It is supposed to connect to an Android device (BLE peripheral) using a bond (encrypted connection with...
Hi everyone,
I went through the source code by Vidar Berg for background dfu using SDK 15.3. I am working with nRF52832 , S132 and SDk 12 with Keil IDE. I did try with secure...
Hi,
I am currently developing with nRF52811 chip using nRF52840 DK. Where can I find a reference 2.4GHz PCB antenna design document?
Thanks.
Regards,
Jxq
Dear Team:
Hi team,I just want to know:
1.Can the ESB protocol call the frequency hopping of Gazell? Is there a corresponding description and source code?
2.Can the...
hi, i am facing this unknown error at "unknown function at 0x000008C8",
i am doing a development project with nrf52832(sdk14.2 and s132v5,ble nus is used) mcu and sim800...
Hello, I'm developing SAADC on nRF52832.
While developing, I have problems now.
I applied sine wave on ADC input.
And the result is displayed on the figure that I...
Hi:
Use the nordic official nRF52832 development board , The software is SDK15.3(example: ble_app_uart ),
Find that there will be a continuous reset. What is the problem...
Hey all,
I am trying to run the "nrfx_spim" example on my nRF52840 USB Dongle (Makerdiary nRF52840 USB dongle), however it is not working. It looks like the code is never...
I have been testing the softdevice codes on NRF52840 DK with NRF52840 SDK 15.2.0 which is working perfectly. But when i put the same test code in our custom board having BT840...
Hello,
I'm still trying to deal with the CLI-coordinator and I have a problem. I am using nRF52840 chip and SDK 4.0.0.
I just can’t understand how I can find out from...
Hi,
I ported an nrf example from nRF5 SDK version 12.3.0 ble_proximity to segger studio (v4.50), and flashed into nRF51DK, using build and run option. The application is...
