Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hello,
When CONFIG_PROVISION_CERTIFICATES is y and certificates are defined in certificates.h the program fails in provision_certificates() function, the modem_key_mgmt_delete...
Hi,
I am working on Bluetooth peripheral and pin_interrupt_change program in nrf51422 on sdk 12.3 .
so I added pin_interrupt_change program in the ble_app_uart program...
I'm attempting to synchronize/correlate measurements made by two separate nRF9160 devices and was hoping to use a timestamp to do so. Essentially I would like to measure the...
I am using GPIO interrupt event.
And I added the following code because I wanted to observe PA / LNA.
Adding this code stopped the GPIO interrupts. Can the two coexist...
Hi,
For nRF82540 dev board, the secure bootloader code has embedded many NRF_LOG_DEBUG(...). But they are not displayed or output to virtual COM port. Is there anyway to...
Hi all,
I'm looking to develop a proprietary start network that may support around 30 devices, with very low bandwidth (pretty much just a keep alive and a sensor state...
I just came upon a blog post from ARM about the use of the Cortex-M4's FPU:
https://community.arm.com/developer/ip-products/processors/b/processors-ip-blog/posts/10-useful...
Hi, I am looking for sample code that can reconnect to bonded devices and share the encryption keys with DFU-OTA.
I have worked using DFU-OTA (JUST_WORKS option); I question...
hi all,
i can't update new nrf cloud certificate
"There was an error generating the certificate: No Nordic product with device id nrf-xxxx...(imei)and ownershipCode...
Hi.
I have a Thingy91 that I will use as a remote wake up for another system. I am trying to estimate how long the system will be able to run on a single charge with the...
Hi!
I am trying to find an example project for the Rigado BMD-340 eval board, or some guide to getting running with this board. We are working on a new product using BLE...
Hello,
I am using peer manager to handle security and bonding. Everythin works fine (bonding witth MITM).
However, when a known peer connects, I am getting 6 (six) PM_EVT_PEER_DATA_UPDATE_SUCCEEDED...
I want to make The Thingy91 a bluetooth peripheral device . I want it to send the generated temperature data to cloud or another device. How do I do this? I had problems with...
Hi Nordic Team,
Please share logic to scan specific peripheral devices which are advertising with a filter other than filter for device name, uuid, short name and MAC address...
Hi,
I am using nRF52832 with SDK v16 with s112 BLE stack.
I am trying to enable the DIS service like below:
The device can boot successfully but when I checked the...
