Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi,
We're working on making some more tutorials, we have some thoughts on what we want to do, but we would really like your input. After all it's you, the user, who will...
Hi
Is there a way to tell that when a connection occurs if it occurred over 1M or 125kbps modulation? From what we can see, the ble_evt->gap_evt->connected does not contain...
Hi all I just want to use UUID advertisement in solar beacon code for advertising @ 100ms interval I don't need temperature and pressure data .I also want to change type to...
Hi. I'm using the NRF-52 DK (PCA10056) with an SD card module and I'm trying to upload the FatFS example code for SDK 15. I'm using a kingston 8GB SD card and I'm unable to...
Hi all,
I develop program code based on nrf-mpu-magnetomter examples. I code the DMP and complied well . However the program is always stay an error when it starts running...
In my application an nRF52832 acts as a BLE peripheral device which is sending sensor data to an app on a mobile phone. As long as the phone is interested, notification on...
I'm trying to add buttonless DFU to the SDK's template application.
Here is my setup:
Soft Device 6.1.0
Secure Bootloader
Modified Template App (Added buttonless...
Hi,
I am using nrf52832 custom board with s132 to read data from 4 sensors using twi. i have 2 separate TWI with two different sensors on each bus. i am using nrf_drv_tw...
Hi,
I have a question with regards to the system-on sleep current of the nRF52840. This is specific to when using the bluetooth mesh and the nrf_mesh_disable() function...
Hello I am trying to connect nRF52832 development kit to use with Wireless vibration controller store.ncd.io/.../ using mesh module which is transmitting the data to the receiver...
Hi
I'm trying to combine NUS central and peripheral in a single nrf52840. Using SDK V 15.0.0 and softdevice V 6.0.0. Have added both ble_nus and ble_nus_c files and enabled...
I am trying to add Timer2 to light_switch server example. But it fails to compile with a undeclared error for NRFX_TIMER2_INST_IDX. I have set the following macros in sdk_config...
Hello all,
I plan on using the blinking LED authentication in mesh configuration, I have seen the nrf mesh app video where it is done using the app but I want to achieve...
Hello.
I am using the NRF52832 Evaluation board.
If I click the connected board of Device Manager to upload program application, nrfgo studio will be turned off without...
