I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Dear, manager.
Hi,
I am currently testing the use of TWI and BLE together.
However, Data (24bit) is received and read through TWI every 4ms. BLE is only initialized...
Hello,
We are evaluating SDK 17.0.2 USB MSC example.
If we connect the PCA10056 board to USB the Windows make System Volume Information folder,
so if we don't make safely...
Development environment SDK 15.3.0
I am working on overturning the saadc project based on ble_app_uart.
The input frequency is 50~2k Hz.
Terminal and debug monitor...
Hello I'd like to output two PWM alternately. Using the timer, PWM1 and PWM2 alternate outputs every 5 seconds. And I want to change duty cycle according to adc value.
...
hello,
i am using nrf52840 in our customised board and trying to interface it with GDEW0213Z16 2.13 inch display which uses spi communication i have added the necessary...
Hi,
Currently, nRF91 supports only one MIPI RFFE-controlled device. In our solution, we would like to have two MIPI devices - one pair of LTE switches as in Thingy:91 for...
Hi ,
Technical Environment details:
nRF Connect SDK
segger Embedded Studio
nRF5340 DK board
1. I have enabled immutable bootloader and MCUboot bootloader.
...
Hello,
Per the datasheet, VDD_GPIO must be applied after VDD has been applied. Is there a minimum or maximum time?
For example, can VDD_GPIO be turned on 1 second after...
Hi,
I am evaluating nRF5340 for using it in a smart lock product with high security. I had evaluated nRF52840 before this
and was impressed with the integration that the...
I started with the ncs-display-ble-example which worked fine. Next I took the LVGL lv_demo_widget, ran it in the simulator using visual studio 2019 where it ran fine. Then...
Hi everybody.
Now I trying to make BLE central device.
I'm using nrf52832.
SDK : 17.0.2
SoftDevice :S132 7.2.0
(I'm completely new at nrf52 product.)
In case of...
hello
I'm currently developing a system that requires a nrf5280 to transfer data to an android phone through ble.
I've based my application on the Object transfer service...
I am entering the saadc source code based on ble_app_uart.
devzone.nordicsemi.com/.../i-am-creating-a-saadc-project-based-on-the-ble_app_uart-project
The source code...
I am advertising services, characteristics and descriptors. All are seen by nRF Connect (for iOS) but in the log I see this:
[Callback] peripheral(periphal, didDiscoverDescriptorsFor...
Hi,
We are currently evaluating a project, that uses the nrf52840 with an SD card and is connected as a USB device. One of the uses is the MCU is writing data to the SD...
