Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
Are the iOS and Android Mesh libraries hosted on Github ( https://github.com/NordicSemiconductor/IOS-nRF-Mesh-Library and https://github.com/NordicSemiconductor/Android-nRF...
Using the nRF Connect toolchain manager on Mac I get the following errors when downloading any SDK.
I have also tried using the manual SDK install process but get...
Hallo everyone,
I have interfaced LIS3DH with nRF52832 and reading a value as below
X 230
Y 249
Z 54
How to convert this value to standard acceleration unit...
I am using the nRF5_SDK_17.0.2 "examples\ble_central\ble_app_blinky_c" example to start with my device.
It works using "init_scan.connect_if_match = true"
However, my...
Hi, all
I'm using nrf52832 pca10040, s132
I've asked several questions, but I haven't found a solution yet.
I want to send data through uart to the custom board.....
Hi,
I am trying to extract the static MAC address from a 52832 using NCS.
I do not want to try to read directly DEVICEADDR[0] or 1, but use a clean function.
I tried...
Hi People, I hope I can get help here or get pointed to a right forum where this can be answered.
I am using u-blox NINA-B306 (based on nRF52840) in one of my custom made...
Hello,
I am using the address resolution function getaddrinfo. Everythink looks fine, however I am wondering which DNS is used for that and if it is possible to update the...
Hi,
I am trying to do a quick PoC to connect some thread nodes to the cloud through a BorderRouter(RPi3b+ running Nordic Border Router, connected to a router using LAN...
I started with the peripherals/spi example, and am now trying to update to the recommended nfrx drivers. I can get the spi working fine, but I can not get the linking to work...
I am setting some manufacturer specific data to broadcast using sd_ble_gap_adv_data_set().
The data gets sent out perfectly when the advertising mode is BLE_GAP_ADV_TYPE_ADV_NONCONN_IND...
In my application, a host co-processor controls when to start/stop advertising, connect etc.
I've noticed that soft-device command are state-dependent, e.g. calling ble_advertising_start...
Hello, I discovered strange behaviour related to reset pin on my nrf52833 prototype and SDK17. My board has only reset button connected to reset input and 10K pull-up resistor...
Hello,
I'm having an issue with a hard fault when trying to write a specific value to a peripheral chip (TDC7201) register after multiple successful writes to the same register...
Hi all,
We're starting to move to the nrf52840 platform and have a question about the adc.. We'd like about ~13 bits of effective resolution- right now we use an ads1115...
