Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
Hi,
I report some problems.
I have been using keil5,it work well. Because nRF Connect SDK doesn't know Keil
now i have used Segger Embedded Studio for a period of time...
Hi everyone. Here is my code for 2 different timers that put uc to sleep and wake it up(supposedly)
Definitions:
Create Timers:
Handlers:
Main() function...
I am working with the nRF5340 DK.
I am looking to sample an ADC pin to sample at a sampling frequency of at least 1kHz and I would like to use DMA to write the data directly...
Hi everyone, I implement nrf5_SDK_17.0.2 ble_app_uart example, but when I connect both GND wire and TX wire of the external device to my nRF52840 DK first, my nRF52840 DK...
Hi
As mentioned in this question: https://devzone.nordicsemi.com/f/nordic-q-a/69533/set-tx-power-on-zephyr-device , there is a sample to change the tx power using some HCI...
Hello,
I am trying to use the ble_app_rscs example app into the nRF5_SDK_17.1.0 package for connecting the nRF52840-DK board to the nRFToolbox Android application. However...
I have a small program that is to be used in production to test my device. It has to be scriptable so I'm using teraterm over rtt.
No external IO for a serial port.
Everything...
Hi Nordic,
Can you tell me how to remove commissioned a node from open-Thread ? Basically I want to remove a node from one network and put it in some other network. Are...
Hello,
I encountered a problem while trying to flash my PCA10040 nrf52 development kit.
I am able to compile my code in Segger Embedded Studio without a problem. The chip...
Hello:
I am using an nrf52840 on a custom board with W25Q01NV NOR Flash with the Nordic QSPI-NOR driver. Programming is with NCS v 1.8.0 (upgraded yesterday) and the VS...
Hi Team,
I am developing an application that required SPI communication with msp430.
But, some received characters are disorders, I see them by JLinkRTTViewer logs. For...
Hi
I'm using nRF51822 xxAA (256 Kbyte ROM). My code size are 66 690 byte, I'm using IAR.
Application memory setup:
This means that I have 131 KByte code size for my...
Hi,
I'm trying to configure my LTE modem (Icarus Board + nRF 9160 + SDK 1.7) with an external SIM.
For that i have to use the PDP configuration.
I use in my prj.conf...
Hi,
I am using SES and NCS SDK 1.6.1 under Win10.
A GPS module is connected to NRF5340, using an UARTE to communicate. The pin receiving GPS data is P0.31.
It works...
Hello,
I want to make sensor sleep and wake-up according to VDD.
- When VDD is below 2.8V, Sensor sleep.
- When VDD is above 2.8V, Sensor wake-up.
Since my board...
