I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi, I'm using nRF52 DK to develop and PPK v1.1.1 with Power Profiler app on nRF Connect v3.3.1 to measure current.
1. I see a lot of posts referencing the firmware on the...
Hello.
I have a issue about missing NRF_DRV_SAADC_EVT_DONE event in saadc handler.
setup is 52832, SDK 15.3.0, S332. enable ANT, BLE
for battery, sensor, I use 2 adc...
When I run the BLE peripheral HRS example on the eval board and try to connect with a Samsung XCover3 using the "nRF Connect" app, I got the error 22 (0x16): GATT_CONN_TERMINATE_LOCAL_HOST...
Hi, we are considering using Gazell on the nRF52840 with nRF5 SDK v16. What would be the maximum packet length and the maximum data throughput that we could expect? What would...
Howdy,
I am using NRF5 SDK v15.0.0 on an nRF52810 custom PCB and am having a problem where the specified event handler is not being called upon completion of an SPIM transfer...
After unpacking I followed the first step at nordicsemi.com/thingy91, which is to update the firmware. I followed the linked instructions to update the modem and application...
Hi,
I have few questiones to initiate developing our project taking BLE Examples and BLE Services as reference.
Now,First thing we have to do in examples is turn bluetooth...
nRF Connect v3.2.0 - LTE Link Monitor is running on Ubuntu 16.04, and nrf9160 fw is v1.0.1. When connecting the board to my laptop, all Modem, UICC, LTE, PDN are Green. But...
hello
i am working with nrf52832
my code is based on the Ble blinky example from centeral. i added to the code with ble, uart, saadc and pwm and it was working great ...
Hi,
Using nRFConnect for desktop I've noticed that when writing an attribute I usually enter the hex values of a byte array (e.g. "12" = 0x12) but on other occasions the...
Hi Nordic Team,
- Can I UART/SPI/I2C on any pin of NRF52832 which is mentioned general-purpose I/O pin ?
- Can NRF52832 wakeup via any general-purpose pin?
- Is there...
Hello My ap plic ation is based on your bootloader (secure_bootloader_uart_mbr_pca10056) and your example "ble_thread_dyn_mtd_coap_cli".
When I send a special command...
Hello everyone!
I just got a Thingy: 91 and followed the startup guide, updated the firmware, and installed the modem...
I had trouble using iBasis eSIM because there...
My question is how to handle large amounts of data over the Gatt service
Our Current setup is 10 devices all on a Mesh Network. We use nRF5 SDK for Mesh and NRF mesh BLE...