I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I have an application where I cannot use the FIFO buffers (HW or SW). Therefore I need an interrupt for each received byte. If I try to use the uart driver (nrf_drv_uart...
I'm trying to program my nrf52832 with an ST-LINK /V2. I can't get both the softdevice and my app on the chip.
Flashing each one seperately works fine but then when I flash...
Hello there,
I'm trying to flash my custom nrf52832 pcbs(untill I get my DKs in the tech tour with a reconfigured stm32 disco board's SWD port with keil uVision using the...
Hello.
This is my code to "wait until micro sd card is pluged".
while(1)
{
disk_state =disk_initialize(0);
if(disk_state==RES_OK)
{
NRF_LOG_INFO("Initialize...
Hello community,
I have a central device which I implemeted, it is running with SD 132 v 4 ("NRF_SD_BLE_API_VERSION=4")
) the chip is a NRF52832, I have some movement...
I have no idea how i can install this and use it.
I would like if any one can explain in detail.
Can you get picture how I can do it?
I am using ble_app_hrs_nfc_pairing...
Hi,
As of now i am using nRF52840 and SDK 14.0.0 and i can find only BLE examples and i wanted to work on bluetooth 5 where can i find examples?.
And i want IR generator...
Hi ,
I am not sure if it is the right place. I was looking for WiFi: 802.11 b/g/n 2.4 GHz support in Arduino UNO and stumble into Arduino primo, which is developed in cooperation...
Hi,
I would like to only connect certain routers in a network using whitelisting. At the moment I'm trying to set a dedicated MAC address to a router and then use this...
Hi,
I am trying to implement the DFU ANT Bootlaoader on my PCA100040 board. I have uploaded the softdevice S212 and the bootloader with nRFgo Studio. I have an ANT dongle...
Hi, I want to read the StaticPasskey from the Softdevice that was set before with:
uint8_t u8_ToBePassKey[];
/*
* Configure ToBePassKey in some way...
*/
m_static_pin_option...
Hi everyone,
I am developing a remote control using nRF52832 chip. My prototype is currently developed in PC10040 board. The IDE is Eclipse Oxygen, and the SDK is S132...
According to here , pstorage_init should not be initialized twice.It links to another thread and the documentation which says the same but does not mention downfalls of doing...
