I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
HI
when I try to uninstall/remove my connect sdk, tool chain manager says:
Failed to remove C:\nordicsemi\v2.6.0, operation not permitted. Please close any application...
Hi I have been working on an project using nrf5sdk_17_1_0 using Segger 5.42a but when I try to build the Blinky example it gives me build failed without any syntax error
We are developing a sleepy end device using the nRF52840, based on the light switch sample. We have set zb_set_ed_timeout to 16384 minutes, which is approximately 11 days...
Hello,
I am using the NRF52832 in my PCB design, and I have attached a screenshot of relevant part of the layout. My PCB manufacturer pointed out that some vias overlap...
Hello,
I have had this issue from the first time I installed VS Code and the nRF Connect Extension.
When I open my project, the connected devices pane is just missing...
Hi,
Since we started testing the new nRF9151 with the latest modem firmware (v2.0.1), we’ve noticed a change in GNSS behavior compared to the nRF9161/v1.3.6.
Recently...
Hi there!
We're trying to port the FreeRTOS Cellular Interface to work with the nRF9160 which is running the Serial LTE Modem application. The problem we are facing is a...
i have a nrf52840dk that is flashed with a old program i used. i want to try the nfc tag and read it using my phone. what should i flash to my nrf52840dk in order to use it...
Hello,
I am building the existing WIFI station app for the Thingy53 with the nRF 7002EB board - sample code: nrf/samples/wifi/sta
In the CMakeLists.txt file, the line...
Hi,
we are now using nRF Toolbox -> Logger tool on our phone to monitor Thingy91 application information via UART/BLE.
Now we would to monitor/log the same information...
Hi,
I am using NCS v2.4.2 and nRF5340DK + nRF21540EK but I can not enable GPIO+SPI mode.
for example, I use nrf/samples/bluetooth/central_and_peripheral_hr application...
I manage to connect to the network and disconnect from it after sending the data, but if I'm in an area without reception, the device tries to connect and after a while, the...
: Chip Not Recognized by J-Link
I need advice from someone familiar with the nRF9160-SICA-B1A-R7.
I purchased an nRF9160-SICA-B1A-R7 chip individually from Digi-Key and...
Dear Sir :
We are now developing on nrf52840, with ncs v2.6.1 and zephyr.
We want to put I2C0 to PM_DEVICE_ACTION_SUSPEND before sys_poweroff().
Our code is below :...
Hello everyone,
I am currently trying to get a ML model running on my nRF52 (preferred nRF52832 but nRF52DK works also for me). Right now I am trying to evaluate if my setup...
