I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Dear All, I am trying to add a custom service on the ble_template_app that I have managed to run successfully on the nRF52820.
I have successfully created the custom service...
Hi,
I am using the nRF52840 BLE chip and i need to connect the external RTC(M41T62). I have one doubt M41T62 is having the 32khz o/p pin where should i connect that connection...
How does one configure the LF clock source using the new nrf connect SDK ?
(not nRF5_SDK)
I don't see any option for then when doing
west build -t menuconfig
Hello everyone,
I have nrf52840 usb dongle and I want to implement meshSDK/ble_app_uart_coexist example for uart-mesh communication.
I follow all instructions on example...
Let me know How to measure RX Sensitivity by TESCOM TC-3000
My S.W engineer setup TX power +8dBm then He wants to know How can it measure Rx Sensitivity
nRF52840_PS_v1...
Hi
I put the MBN52832 (nRF52832) on my WSM-BL241-ADA-008DK to test the SPI (see the user guide here ).
The sample "peripheral/spi" from SDK ver. 16.0 is used for the test...
Hi everyone I have been trying to use UARTE1 + UART0 combination for a device that i am working on, I have implemented the UART0 using the nrfx_uart library and it works fine...
Hi,
I am using nRF52840 to communicate with the EEPROM. 24AA32AT-I/MC over I2C interface. The TWI scanner example detects the EEPROM address correctly for me .Now, I want...
Hi Team,
We are using nRF9160 DK, we tested that asset tracker application, that was working fine, We also tested the aws_fota (firmware update via AWS) that was also...
I want to develop a mesh network where I can send/receive data from one device to other devices(sleepy sensors) through relay/router node (always on).
For example
A (Publish...
Hi, engineer:
I need to compute FFT on nrf52840, I used sdk-demo fpu-fft, I tested the FFT operation time and found that it took 2 ms，That`s a long time, Did I configure...
Dear all, I have a problem with nRF52811 GPIOTE input interrupt. I have one sensor interrupt pin at GPIO P0.30 with external pull down resistor. I am able to config P0.30...
Hello community,
I have programmed my dongle as beacon. Now I want to stick them to the wall for experiment purposes. How is it possible to power them up via external...
Hello
I am considering a product that connects several NRF52840s to a USB 2.0 7-ch HUB and works with 30 BLE devices. When reviewing a product like this, there are some...
Hi everyone,
I have one question just for confirmation.The available analog pins on nRF52840 DBK are those provided by header P2 (six in total)?
Are there any more available...
