hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
I'm currently using a HostController with pregiven communication protocol for transfering data to the NRF52840 (over uart). The NRF is flashed with the SD140 and I'm using...
Hi Dev Zone Team,
I had a question regarding the current measurement of Nordic Thingy 91. I am following the steps provided in the Thingy91 documentation.
I have a Joulescope...
Hello.
I am testing saadc function.
When I was connect the saadc pin with ground level, the saadc value represents negative value.
So I am searching the similar problem...
Hi:
I'm coding with the nrf52840 dk sample.
as we know, the gatt operate is notify,read, write, etc.
I have found the event about the write,and notify:
case BLE_GATTS_EVT_WRITE...
<environment> Windows10 ncs v1.3.0 modem fw v1.2.0 DK 0.9.0
I made one-shot agps app by modifying gps sample app. The behavior is this.
- download SUPL data from supl...
Just bought 2 nrf52840 DK's both stopped working
Observation
Was able to program and run SDK examples.
Above working setup not disturbed,so all cables are in order...
Hi, I'm using nrf52 dk and struggling to get low power consumption using multi_sensor_freertos ZigBee example from nrf sdk. Can you provide me some guides on how to optimize...
Hello,
nRFSD5 v16.0, softdevice v.7.0.1, nRF52811
I want to detect power failure/low battery voltage using POF feature of nRF52811 chip. Here is the code I'm using:
...
I am trying to capture audio PDM samples at every 5s interval blocks, but at the time of "pevt->buffer_released" event when i am giving the new buffer to PDM driver it results...
Hello, I am working on the NRF9160DK card. I am using SDK 1.3.0 and the latest modem uploaded: www.nordicsemi.com/.../Download 2020-04-29.
Whether it's with the asset_tracker...
Im following the guidance to upload modem code and application code, downloaded from project page, onto the Thingy:91.
Current state, after following guidance, is: I hold...
Hello,
Currently I have implemented a UART callback using the CONFIG_UART_ASYNC_API setting as follows:
However, all data that I receive is appended constantly, until...
Hi, I want to measure the data transfer speed of BLE. I use the nRF52840 DK with the ble_app_uart example
I created a dummy string of 20 bytes (default length of one packet...
I have a shipping product with S132 2.0.1 with multiple problems with the LFRC clock.
There are seemingly at least 4 errata that apply (77, 132, 146, 192).
Are there...
Hello, I'm trying to compile the LIBUARTE example from SDK 16 but im getting undefined reference errors, this is what I've done so far:
in sdk_config.h defined , (I've...
