I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hi,
I have implemented a hx711 sensor readout with PPI, using SPIM and PWM peripherals. But for this is needed 4 GPIO and one external OR Gate. I wait for a LOW pulse on...
I came across the nrf-connect SDK sample UART : https://github.com/Rallare/fw-nrfconnect-nrf/blob/nrf9160_samples/samples/nrf9160/uart/src/main.c . I was wondering whether...
Hi team
I want to config interval via LL_CONNECTION_PARAM_REQ.
But nrf5 looks like use L2CAP CONNECTION PARAMETER UPDATE REQUEST to send request to change config.
But...
Is there any reason the pin reset hold time is not mentioned in the nRF52832 product sheet? I've seen in the forums that it is same as nRF51, which is 0.2 uSec but I would...
Hi
We are using BL600-SA in our project. I need to configure NRF51822 transmit power so that it is discoverable at particular distance.
I am using softdevice S110 and...
Hi.
I am newbie and trying some sample examples from nRF52832 SDK for mesh to gain knowledge of Bluetooth mesh
I have nrf52832 Development Kit and I am trying examples...
Hi! We're developing a BLE-sensor for tracking small animals. In the past we've used a different brand of BLE-module but we're looking to switch to the nRF52840. As we're...
I want to use my "nrf51 DK" module as a BLE sniffer for which guide is provided at https://infocenter.nordicsemi.com/pdf/nRF_Sniffer_UG_v2.2.pdf but I also need " nRF Sniffer...
Hello,
I cannot connect Thingy91 to NB-IOT or LTE-M network. I am in the UK, so I am trying the NB-IoT with an O2 sim card. In LTE Link monitor I am unable to get a connection...
"There was an error adding your device. It wasn't found. Is it connected?"
IMEI and PIN entered several times.
I do not want to post the ID's here.
By the way: HW...
We are producing a batch of nrf9160 based devices and will need to upgrade the modem firmware, this will be much easier if we could do this through the command but I saw on...
OS in development environment ：Windows7 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex-M4F 32 bit processor...
I'm using the nRF52DK as a nRF Sniffer for BLE, following the directions in the nRF Sniffer User Guide v2.2. I'm using v2.0.0 of the sniffer, along with the Profile from v2...
When importing projects into SES, it does not appear that SES can determine configuration macros.
For example, in the mqtt_simple project, the function "modem_configure...
