Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I want to use ANT and BLE concurrently.
I found that there are no multiprotocol examples in SDK12 for NRF51422 (PCA10028). It only have example for NRF52832 (ble_ant_app_hrm...
Hi all,
i use softdevice and app timer.
I know that the softdevice use a RTC0 and app timer RTC1.
I would use a rtc to have a timestamp. but i see that after 512 second...
My function need a time window to get value from sensor,but the prcess always interrupted by SD.I know that the priority of SD is higher than app functions. So how can get...
Hello friends. How to write a number to and read from internal flash. My information about the microcontroller is very weak. I use STM32F103RET6 .
I test The following program...
Hello,
I'm starting to program a Nordic microcontroller, the nRF52. I was able to compile the various examples.
Now I would like to create my own project and use the...
The FDS requires data to be word-aligned and multiple of the word size. How do I ensure that my source/destination data structures are properly sized/aligned?
E.g. I want...
Hi, would like to know if anyone has some experience and advise how to get an external 51822 based board programmed and working via the nRF52DK. All the wiring works, I can...
pc cannot recognize nrf51 DK board.
what I have done.
erase all - not work (log.log attached)
power on with reset button. and copy J-Link OB-SAM3U128-V2-NordicSemi...
I have 5 nRF52832 development boards.....
I'm using Visual Studio 2015 and a Visual GDB plugin.
I have loaded and built the BLE Le example.
I start the debugging...
I'm using SDK 12.2. The FDS operates on word-sized data. How can I ensure that my data structures are word aligned and multiples of the word size? E.g. if I'm trying to write...
Hi everyone,
I am looking for reports and/or certifications that can help with our own device's certification process.
Would you know where we could find such reports...
Can I configure security parameters my own way?
I read some BLE profile but there are not explain about security configuration.
And I tested by using PCA10028, iPhone4s...
I am trying to setup an interrupt to fire whenever any of 6 GPIO pins change value using an nRF51822 with soft device. I found the example that uses GPIOTE to get an interrupt...
Hi. I'm using nRF51822AC, SDK12.2.0. S130 v2.0.1.
I just want to make DFU program. But I think it's a little bit confusing. So I want some explain.
Q1. What is the difference...
