FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
On our platform we have the following configuration of firmware:
Master boot record
Boot loader
Thread application (compiled separately from the boot loader)
We...
Hi,
I am trying to write a file with dummy data on my internal flash memory mx25r6435f of nrf5340. Then read back from the file and see it in putty. Here is the folder...
Hi
I have an external NOR flash chip which is powered off on startup. The idea is to power up the flash when needed to reserve power. On startup, I get the error message...
I haven't found much documentation yet regarding multiple threads in the secure partition, so I wanted to ask if this would be possible. Was planning to also test it out myself...
Hi,
We have a requirement to not exceed 63 mW of WiFi Tx power at any time for any band (2.4 or 5 GHz) . There is a statement about changing Tx power is not supported. Can...
Hi, We are currently migrating our project, originally developed with NCS version 1.8.0, to the latest NCS 2.7.0, while incorporating MCUboot for both of them. During this...
Hello,
I am encountering an issue with the nrfutil settings generate command. Each time the command is executed with the exact same parameters, the resulting settings.hex...
SoC: nrf52840
SDK: OpenConnect 2.4.4
I have been developing an ambient noise system using I2C microphone, nrf52840 and Zigbee networks for some time. The firmare reads...
Hi,
Is nRF52811 / S140 capable of simultaneously being in peripheral (connected slave) and central (connected master) mode like described in this blog post https://jimmywongiot...
I’m working with the nRF5340 and nNF Connect SDK 2.6.1. I’m encountering an issue where, after a central device (e.g. an Android phone) forgets a bonded peripheral device...
There was a previous discussion about the option to disable/enable slave latency a few years ago:
Did this ever get implemented? Specifically interested in the feature when...
SDK: 2.6.1
I needed to add a single wire support to our device recently and I did that by using two pins TX/RX shorted and UART. It works, but current consumption sky rockets...
Hi all
How would I be able to generate and view the calculated hash that i get while using the dfu library? Is there an easy way. I'm hoping to generate one single hash...
I am looking for the code example of how to setup A-GPS/A-GNSS on a nrf9160 dk, but I am not able to find one. I am only able to find these links:
https://developer.nordicsemi...
Hi everyone, I'm encountering an issue with MCUboot on NCS 2.7.0 and my custom board based on the nRF52840. The bootloader was functioning correctly with NCS 2.4.0, but now...
