Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Hi,
I am working on a smartwatch PoC using the nRF7002 DK (nRF5340), and I am trying to interface a 1.8" ST7735 SPI TFT display (128x160).
Hardware: - Board: nRF7002DK...
Ultrasonic welding is commonly used to seal plastic enclosures for electronic devices. 32kHz crystals can be damaged by this type of welding and manufacturers recommend not...
Does APPROTECT supersede SECUREAPPROTECT or do both need to be enabled for maximum security?
Similarly, do the HW protections (APPROTECT, SECUREAPPROTECT, ERASEPROTECT)...
I am trying to measure current on a nRF52 DK v3.0.0 using PPK II in source mode.
I cut SB9 and soldered SB12 as described in this guide: https://docs.nordicsemi.com/bundle...
Hello , I 'm trying to use the Lan865x (two -wire eth click ) chip with the nrf52840dk board , using zephyr 3 . 7 . I 'm getting always this error while trying a net sample...
Hello!
I've been trying some of the solutions around these forums but I can't seem to get my nRF52840 DK to show up on my device manager so I'm unable to flash anything...
NCS 2.7.0, NRF52840, SYSBUILD with MCUBOOT
We have 1 specific board which is failing with a hardfault and assert MPSL ASSERT: 112, 1617 it occurs whenever we activate...
Hello Nordic Team,
I am using nRF Connect SDK v2.9.0 with the nRF52833 controller. I am currently working on OTA implementation.
I am implementing OTA in another code...
I want to prototype an Auracast transmitter, with an analogue audio input, which is also WiFi enabled. I have read that the recommendation to get started with the nrf5340...
i'm measuring approximately 1.5uA (at 3V3) when sleeping between BLE advertising events, using a program based on one of your the standard examples.... as an experiment, i...
There expect to be a physical limit to the number of components an AHB can support.
For instance, if 8 different masters (Including App core, Net core, several peripherals...
Hi Dev,
Development platform: NRF54L15 + NCS 3.2.3. We are using the GRTC SYSCOUNTER as a system timestamp. Under normal conditions, a software reset does not clear the...
As the title, I have already tested the ESB routine (esb ptx Sample/esb prx Sample) by using nRF54LM20-DK + nRF54L15-DK. There was absolutely no problem. But when I added...
Hello,
I have a project in Visual studio code and Nrf connect.
MCU is a NRF 52833.
For the certicications, the lab request me the DTM mode.
I tried the use the Sample...
