hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
Hello,
I am working with Window Covering cluster.
I receive command ZB_ZCL_WINDOW_COVERING_GO_TO_TILT_PERCENTAGE_CB_ID from my coordinator successfully, but I can...
Hello
I need to broadcast large amount of data on MQTT ~ 300K
I require to send it as fast as possible
how can I best calibrate settings for maximal speed send via...
i am using ble_app_uart example on nRF52833 board. I want to make a function that whenever I press button 1 on board, the board will disconnect Bluetooth connection with my...
Hello,
We are developing a BLE beacon with nRF52810 and SDK17.0.0. I modified the code on the basis of ble_app_beacon. I rewrited m_advertising.adv_modes_config.ble_adv_fast_interval...
Dear friends:
The ble advertiser device can advertising, the advertising can be monitored by a smartphone.
The ble mesh node with proxy feature also can advertising, the...
I encountered an issue where my firmware would get stuck in NRF_LOG_FLUSH();, and the same logs would be sent over RTT repeatedly. Pausing the debugger showed that the read...
Hi
My purpose:
Send 180 Bytes per 10 millisecond
I got a problem:
I use NUS project in NCS SDK15.0,when I send data per 10 ms,It return"Failed to send data over BLE...
To the kind attention of Nordic support team,
We would like our BLE nRF52 based product to reconnect as fast as possible.
My question is: are there side effects in having...
Hi,all
I want to connect my NRF52832 device with pc, then , use the value uploaded from the device to draw a curve in pc. Refer to nordic engineer's advice, i used the heart_rate_collector...
I want nRF9160 to do mqtts connection without certificate.
Modem FW:1.2.3
Here is my mqtt client_init:
When I use 9160DK, mqtts is connected normally. But when using...
Hi Everyone, I am confused in sleep modes of nrf52832. Can you please tell me the difference between System ON sleep mode and System OFF sleep mode?
also the current consumption...
Dear friend，
Based on SDK15.3, using S332 protocol stack, running on nRF52832-QFAA. Connect the device with a mobile phone via Bluetooth. The connection parameter Min connecion...
Hi,
I am trying to get the current time, using nrf9160 dk with v1.5.1. I tried using the following functions
proj.confg. tried enabling/disabling based on devzone case...
Hi, I am new to thingy52 and raspberry pi and now I am trying to connect 4 thingy52 to a raspberry pi to get the data from those sensors.
I have followed the Nodejs examples...
