Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hi,
I'm using NRF52840 in order to connect to a mobile device, with PIN code.
Connection to Android is ok. The issue is with IOS.
IOS can't send the PIN code to my...
Hello, We're trying to optimize the data transfer rate from our nRF52832 based peripheral device to the mobile phone. Tested with two different BLE >= 5 Android phones we...
Hello, I ve made a custom nrf52832, but ive face a lot of problemes : when logs is on the BLE is off(its not advertising) , I m not able to see it on my app. when my module...
Hello,
I am using MacBook and would like to import Keil Projects into Segger Embedded Studio by following this guide , but finally I got an error is that
I have found...
I have some questions about nRF9160.
1. What is improved comparing to revision1? Only power consumption?
2. Is GPS sensitivity improved? In revision1, it is poor.
3...
Hello!
I use light switch example in a 52DK with a 4.1.0 mesh SDK. I modified the original project and implemented the custom element model for sending arrays via mesh....
Hello.
I'm testing the integration of the BLE and TWI.
However, BLE advertising function when turn on, TWI data was not correct read.
Can you tell which one is...
Hi, I am saving data in flash memory but when I read after restarting the device it shows FF. How can I read from flash after restarting the device? and how can I check that...
Hi, i am very new to nrf family. when i use sprintf function with %d specifier, it works fine. but if i set it to %2.1f or anything with "f" included doesnt work and program...
In the ble_app_hrs_rscs_relay application, three ( NRF_SDH_BLE_TOTAL_LINK_COUNT=3) queued write modules are generated.
(one for a peripheral (server) role and two for two...
The first 0:20 sec in video -
in this 20 sec the video shows the ON / OFF switching of led .
The voltage when we click ON is 1.149 and 1.211 of warm and cool respectively...
Hi,
I am using Nordic nRF52832. I wrote the simplest code for entering system off mode. My code does nothing except system off (see below). I built the solution, downloaded...
I would like to use nRF52 DK (nRF52832) to program Fanstel BC805M EK (nRF52805) . I know that the hardware connection looks like this and we need to use the separate power...
Hello,
I want to use / control the nRF52840 Dongle within our own software . We are writing our own production and testing tools in a c-compiler (LabWindwos-CVI) environment...
