Code_Replace_MainDotC.docx
Please look at the attachment of my code. Go to \nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_template\pca10028\s130\arm5_no_packs...
I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
Hello,
i’m using NRF52832 with SoftDevice S132 and Sdk 15.3 to develop a NUS peripheral and central. The system is tested as follows:
I have two NUS peripherals , a NUS...
Hello, I have questions about esim card.
1. Hardware footprint about esim chip.
I don't know which esim chip I will use.
So is there a common standard footprint?
If...
Hello,
I've a board with usb port
I can insert on USB the Raytac MDBT50Q-RX containing the nrf52840 and:
- my microcontroller can recognize it as CDC ACM USB serial...
Hi, I'm Developing Custom Board with nRF52832.
When I execute my custom code (by referring to ble_app_template example), an error occured.
First, my hardware spec below...
Hello, i am using the ble_app_beacon example on the nRF52840 DK with s140 and i want to send the service UUID for Device Information. I inserted the code from the ble_app_template...
i'm trying to get samples/drivers/CAN working with the nrf52
apparantly you need to enable CAN explicitly in menuconfig, which is already confusing because prj.conf has...
Hello. I met trouble, presented in the name of the thread. I use example for PCA10400e board. So, what I've changed to accelerate reproducing of this error. I change logger...
I have a question about the current consumption of GPIO and GPIOTE.
I want to use port in input configuration. Therefore, the following settings are made ("P_WUP_BLE"...
I have following problem:
I am using a multilink NUS Central. With one peripheral connection everything works fine. But when make a second connection I sometimes get an...
HI
We are developing a 2d-3d mouse .
We are trying to implement OTA-DFU into our custom board .
We first tried it on development kit and its working fine too . I can...
Hello all,
Environment:
Rpi with Raspbian Stretch (Release 9.8)
Kernel 4.14.8-v7+
Architecture armv7l
I have followed the below links to build BLE 6LoWPAN environment...
After compiling the SDK 15.2 ble_app_hrs_freertos_pca_10056_s14 example in Segger Embedded Studio there are a number of repeated warnings:
"configTICK_SOURCE" redefined...
Hi,
i've got the TWI scanner example flashed onto the NRF51 dk board, using the default "Arduino" pins of P0.07 and P0.30 as SDA/SCL.
I've added two lines to the example...
I have a small collection of i2c devices on the bus that can be jumpered in (sda/scl disconnected). I am currently using SDK v10 and Keil v4.
I wrote this code to namely...
Hi,
I am trying to use the SSD1306 display with the nRF9160 DK.
I am using the code as is shown here
https://github.com/zephyrproject-rtos/zephyr/tree/master/samples...
