Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Hello ,I hope the speed of NUS can be achieved 7K Byte/s. The data form phone to uart is ok,but the data form uart to phone is not.I tested the Bluetooth part separately.Loop...
Hi,
I am able to connect nrf51822 with nordic app but now i want to receive data from nrf51822. For Example -
If nrf51822 detects some voltage at pin no "1" then it should...
Are there any Segger Embedded Studio examples for the nRF51 dev kit?
All the examples supplied with the nRF5_SDK_14.1.0 seem to be for the nRF52.
I only bought a new dev...
How do you do
E: \ Nordic \ nRF5_SDK_12 _f012efa 2.0-3 d \ examples \ peripheral \ pwm_driver pwm_driver routines of the path,
1.How to configure reverse polarity...
In all the SDK examples all the source is in main.c. Is there a good reason for keeping everything including timer initialization, UART config, BLE setup, etc all in one file...
Hi,
I am using nrf51822 (pca10004) with SDK110 softdevice programmed through j-link LITE SEGGER. After programming the custom code (Basic I2C code) and when we try to debug...
Is there any documentation as to how to connect a nrf52 chip (as found on the nRF52832 BT Module with Header Pins ( www.analoglamb.com/.../) or the nrf51 on the Adafruit bleFriend...
Hello,this is Lee.I have a problem about nRF51822.
When I turn on/off the power 2.8V to it ,it hangs up
frequently.I check POR function,I found that the residual
voltage...
hi,
i'm using the 32KHZ external crystal and i didn't find any free space in my PCB to put the crystal in the same side with the nrf chip, so the only solution that i found...
I am trying to implement a bootloader with rewrite protection on nrf52840 with SDK: 14.0.0.
But it seems that there is no flash write protection registers in nrf52840.
So...
UPDATE: Corrected language.
Hi,
While experimenting with BLE mesh networking using S130 on nRF51 devices and S132 on nRF52 devices, we have a problem with deafness while...
Hello,
I want to save Image data which are come from the central device to flash memory of peripheral side.
The image data size is vary from 3KBytes to 10KBytes.
...
I just came across the following code ..
(hash)ifdef linux
toolchain_init_irqs();
(hash)endif
Does that imply there is a possibility that the source could be...
How can I running the ble_app_multirole_lesc example in debug mode to examine the traffic? I use me network traffic analyzer to view the traffic currently ((debug mode switched...
I want to use several sensors that makes a measurement send the data to server (same as provisioner) and fall asleep. Wake up after 20 minutes and process repeats.
Does all...
