Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
I have now had two units exhibit nearly the exact same behavior, and it seems odd to me for them to be so similar. I'm wondering if anyone else has seen similar. I have a...
Hey all,
I have a USB CDC ACM application that works great when it starts, but I'm not able to get it running without the debugger. This is SDK 17.0.2, there is a SoftDevice...
Hi,
I'm trying to use timers 1, 2 and 3 in my application which also uses the app_timer. It works fine when I'm just use 1 & 2 but after inserting the following code to...
Hi, can you point me to the documentation that tells me what preprocessor defines are required for properly building ble_blinky_c or similar please.
The reason is for setting...
Hello,
I am facing problems when I send 3 consecutive chunks of 244 bytes on BLE. My actual task is like receive from SPI and send it to BLE. I am receiving data in chunk...
Hi,
I need to store the 1kB of data in the flash storage and it need to be read anytime and change the data anywhere.
I am using nrf52840 DK and also nrf5340 DK to perform...
Hi Nordic Leaders,
Regarding nRF5340 and nRF connect SDK
Objective: Update blue tooth data transfer rate between 1Mbps and 2 Mbps.
Details:
As it is not possible to...
Hi I am merging BLE Peripheral code and I have added all .c files and added the path in C/C++ compiler and Assembler but it still shows definition missing
You can see...
we are using NRF52832 for my development. Also implemented 1 custom service. Currently we are using 2 standard services and 1 custom service(12 custom characteristics) with...
Hello, I saw another post with a similar question regarding the same error message from a few years ago that went unanswered, I figured I'd reask the question.
I am attempting...
Dear Support
I think gpio_nrfx_port_toggle_bits() is not task / interrupt save.
When between nrf_gpio_port_out_read() and nrf_gpio_port_out_write() a task switch or...
Hey,
I am working on a project as a internee using acconeer xm122 sensor and nrf9160 dk.
I want to know that how I can connect nrf52840 on acconeer xm122 sensor with nrf9160...
Hello,
I am having some trouble migrating from the nrf52 DK to my custom board with an nRF52832 and running as standalone. The application is working as intended when the...
Having an issue that suddenly started with my nRF5340. Tried swapping out batteries, USB power supplies, cables, still have the following error. What is weird is I don't get...
