In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Good day. Some smartphones cannot connect to NRF52832 (SDK17): - iPhone XR - iPhone 11 Detection goes well, but smartphones cannot fully connect and freeze at the connection...
Hi Sir,
We tried to download the nwp_024 , and check the tape reel information of nRF5340.
But we could not find the nRF5340 lists in "table 2. Carrier tape dimensions...
Hey everyone,
I firstly want to preface this with my lack of credentials. I'm very new to embedded systems development and am figuring things out slowly so please bear with...
I want to initialize LFCLK on startup to reduce power consumption. I am doing it as given below. Is this the correct approach of initializing LFCLK to reduce power consumption...
Hi,
I am using nRF52840 as BLE peripheral, on a Zephyr application under NCS 1.4.2
I want to limit the connection interval to 7.5ms (min+max)
I can see that the only...
Hi Nordic DevTeam,
I am using nRF52840 (1MB Flash, 256kB RAM). I would like to store a log data to flash memory that I can extract them to my Android phone later on when...
Hi All,
I want to verfiy the current consumption of nRF52840. I'm using an nRF52840 DK and SDK 17.0.2 RTC example. below are the verfiy steps:
1. Cut SB40 on PCA10056...
Hi,
I we are developing project on BLE NRF52832 module and it warked correctly. during the debugging suddnely it stoped responging to programmer and couldn't be reprogrammed...
I have read about eddystone protocol. I have run
nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_eddystone\pca10040\s132\arm5_no_packs
i am able to build the code...
Hello
My setup looks like this. I am using nrf5_SDK_for_Mesh_v5.0.0 with nRF5_SDK_17.0.2. I have extended the sensor model example (in nrf5_SDK_for_Mesh_v5.0.0) and call...
Just wanted to get clarity on the usage of RACP. In the Glucose SDK example, every measurement gets saved to the database regardless if a Central is connected or not. Why...
Hi,
[246] System: Intermittent extra current consumption when going to sleep
This anomaly applies to IC Rev. Revision 2, build codes CKAA-Dx0, QIAA-Dx0.
It was inherited...
Hello everyone,
I am new and tried some example on the nrf52840 devkit and dongle, including light switch example.
I am now going to send some ASCII bytes through the...
