Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
I got an error when trying to build the dimming_client_nrf52840 example.
Simple error:
build/dimming_client_nrf52840_xxAA_s140_7.0.1_Debug/obj/ses_startup_nrf_common.o...
SDK 16, S132 V7.0.1, NRF52832, custom device, custom firmware.
Hello,
I want to keep beaconing advertisement (not connectable advertisement) while the BLE is connected...
Hi,
I have a question concerning the SIG qualification. We use the ublox BMD-350 (nrf52832) that is qualified as a component (QDID 101018). I don't really understand the...
Hello,
We are using nRF52840 chip with S140 with ble_app_blinky example.
I was merging Serial DFU bootloader, SoftDevice, application and BLE settings with below commands...
Hi,
I am trying to implement DALI-104 (IEC-62386:104:2019) on top of Thread protocol.
I am using Thread: CoAP Client and Thread: CoAP Server and want to configure these...
Hi,
I wrote my codes to toggle notification on and off using a button using nRF25840-DK and sdk v15. The task looked a simple one; however, I hit some issues such as error...
Hello Nordic Team,
We are working on a project based on nrf51822, we have a problem regarding the incorrect ADC values while waking up the microcontroller from System...
Hello,
I'm developing a custom asset tracker board. My software is currently a very lightly modifed asset tracker v1; my provider currently only support NB-IoT, firmware...
After that one of Zephyr's configuration files was modified (CMakeLists.txt, *.overlay, prj.conf).
How the SES project can be updated in additional to option "Open nRF Connect...
I'm trying to use the board support package (BSP) through a keil software pack, starting from the dfu_dual_bank_ble_s110_pca10028 example. I thought it would be more or less...
Hello, I have installed (multiple times) the nRF connect SDK via the manual installation guide but I still seem to be unable to open any project.
I have tried on MacOS and...
Hello,
We are currently using SDK v17.0.2 with NRF52840, driving a display with SPIM3. We are able to successfully communicate with our display and command it to render...
Hello. I'm designing a board with NRF52832 connected to SGTL5000 via I2S. I'm planning to use the driver found in the Nordic Playground here...
https://github.com/NordicPlayground...
Hello,
Before going into detail, the question is: Is there is any chance that NAND flash will be supported (via QSPI or SPI) by the nRF5 sdk in the future ?
My question...
