Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello,
I am working developing an application that sends data as notification to connected host at the data rate of 2KB/sec. The chip being used is NRF52832 with S132 soft...
Hello there; My setup: NRF52832 SDK 15.3 I'm facing some problems with FDS when i use it with BLE activated.
When i read or write on FDS using fds_record_open or fds_record_update...
I followed the steps mentioned in the Bluetooth low energy Characteristics, a beginner's tutorial, but at "if ((p_evt_write->handle == p_our_service->characteristic1_value_write_handler...
Hi, I tested "Simple_coap_client" and "simple_coap_server" on NRF52840 using Threading SDK.
I want to change the transmit power, so I used "otPlatRadioSetTransmitPower ...
52810, LIS3DH, I call nrf_drv_twi_tx got NRF_ERROR_DRV_TWI_ERR_ANACK return using either TWI/ or TWIM . Here is my code:
const nrf_drv_twi_config_t config = { .scl = TWI_MASTER_CONFIG_CLOCK_PIN_NUMBER...
Hello,
I want to verify with you if the Standby current for My Bluetooth 5.0 corresponds to the system "on" according to the Bluetooth datasheet or there is another way...
Hello, we've built up quite a bit of experience programming Nordic targets with Keil and nRFgo studio. We love your products. However, we are considering moving away from...
I'm trying to get debug output to appear in my Segger J-LINK SWO viewer (from an NR52840 SDK board with NRF5 v16) which I understand is a potentially complicated process;...
I use Peer Manager for storing bonding infomation with nRF52832 (SDK14.2) using gcc.
I understand Peer Manager uses FDS, and FDS uses flash memory from 0x7D000 to 0x80000...
Hi All,
I know this question seems to have been asked many times already but still does not seem to work for us even after checking forum answers.
Hardware: Fanstel BT832...
I have followed up this example and compiled successfully but the NFC pairing is not working at all.
I use my smartphone (Google Pixel 2) to touch the NFC antenna and nothing...
I can control GPIO P0,but can't control P1, when I load project with nrf5340_dk_nrf5340_cpuapp ns configuration.
If I load project with nrf5340_dk_nrf5340_cpuapp configuration...
Hello,
I am using a custom nRF52840 ( SDK 14.2.0, SoftDevice S140) based board to connect with an iOS(v 13.3) phone.
I am running a custom application which uses the...
At this time my project is at very beginning state, I am picking up right tools to start my project development. I have spent good amount of time to research about my issue...
