FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
Hi,
I am using nRF52832 SOC along with SDK v15.2.0 with custom hardware, currently I have requirement to use DFU protocol in BLE application to get a FW of another sub system...
Hello, I hope your day is full of the scent of flowers.
I am in the process of the Ble_Cnetral and PrePhereal project.
I have added and built the Uart.
Why is...
Hi frnds,
I am using the ble_central and ble_peripheral code (nrf52840).
i am sending 400 bytes of data to central from peripheral continuously, sometimes the boards get...
3.19 [78] TIMER: High current consumption when using timer STOP task only
I'm using app_timer_stop. But I do not know how to cope with this errata. Does the timer stop that...
Hi
After upgrade modem to mfw_nrf9160_1.0.0.
Most of our SIM cards still working good on both AT and MQTT projects.
Two of our SIM cards can't connect to LTE when uses...
Hi,
I'm using nRF52840 where it's written 1.0.0 on the jlink ship and QIAAC0 on the nRF ship.
When reading the info.variant register I got 0x41414330 which is ..AAC0...
Hello everyone,
I am using a NRF52840 development kit to write a custom protocol, so for the moment I am not using the softdevice but I am rather using the Radio as a...
We have a board built with the NRF9160 and an ADE9153A. The ADE9153A only responds to messages with odd parity. How do we set the NRF9160 to odd parity?
Hi,
I want nRF52 Continuous Unmodulated TX carrier.
Is it possible by TASK_TXEN and TASK_START or radio_tx_carrier command of radio test example, after TX configuration...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Hi, team I am trying to build a system with one master and multiple slaves using the mesh SDK. ( This is similar to the light_switch example. ) At this, I want to give each...
After the update to nRF Connect v3.0.0 none of the Nordic devices is detected anymore by that tool.
I even un-installed and reinstalled nRF Connect v3.0.0 (as recommended...
Went through the pin_change_int example and of course it works fine.
Migrated that to custom board and it also worked fine with main loop.
So I then tried to use that...
Have an application that configures a wifi SOC using spim before enabling BLE scanner.
When it is running there are 4 timer events running and the main loop check status...
