Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hi Sir,
My project need LESC & AES-CMAC function, then I enabled below CONFIG in sdk_config.h :
NRF_CRYPTO_BACKEND_MBEDTLS_ENABLED
NRF_CRYPTO_BACKEND_MBEDTLS_ECC_SECP256R1_ENABLED...
Hi,
So I am trying to configure the stdout console to use UART1 by default. Using the NrfConnect menuconfig in Segger emStudio I can set it to use UART1 with the following...
Hello !
I have read in DevZone, but still not sure regarding nRF52832 .
For nRF52832 and page size 4k, and regarding only writing zero-bits.
Can I in same page perform...
Hi team,
Here is the previous ticket
https://devzone.nordicsemi.com/support/234693
One of my customer TMC is using our nRF52810 in a BLE key project for central role...
When in dfu mode (with usb dfu enabled) if we jump to application via "
nrf_bootloader_app_start" there seems to be an issue where the firmware locks up and doesn't start...
Hello
my setup is a nrf52840, the sdk15.3, Softdevice s140.
is there a possibility, maybe with freertos, to to run two seperate applications like two threads.
In the...
Hi,
I'm trying to implement a slow timer which is supposed to be triggered about every 30 minutes or even less frequent, but I'm kind of clueless how to solve this issue...
from which antenna these values were derived resp. measured? e.g. there is a pcb antenna and a hirose u.fl connector available on pca10040... examples/ble_peripheral/ble_app_eddystone...
hi,
The software version is nrf5SDKforMeshv310src and nRF5_SDK_15.2.0_9412b96
I use five nRF52832 nRF52 DK. client * 1, server * 4, provisioner by android phone.
examples...
Hi can you help to configure nrf52840 DK board to measure power consumption with keysight n6705C. In manual is described with ammpermeter and oscilloscope. Keysight n6705c...
Hi, I'm new here so please let me know if any additional information could help.
We are in need of encoding speech on a nRF52840 and are working in Opus and are having trouble...
Im getting this error any idea how to solve it this are configs.
Loading solution lte_ble_gateway.emProject
Executing load commands
/usr/local/Cellar/cmake/3.15.2/bin...
If the only supported method is through the PC-based nRF Connect Programmer GUI application, how is a system based on nRF91 its modem firmware once deployed in the field ...
Hello,
I am working on nRF52832 SDK 15.3.0 using segger embedded studio in windows 7.
I am trying to merge two application, one is launch application through NFC and...
