I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
Hi,I had a new project base on nRF52810. I watnted to created a timer, but the note mentioned " increase the value of the macro APP_TIMER_MAX_TIMERS by one ".I couldn't find...
Hi,
is nRF9160 SiP comes with eSIM? or do I need to insert external SIM in socket which is traditional method?
Do I need to external chip antenna? does that antenna...
Hi:
Because our project using much nRF pin resources, we have to use the defualt function NFC pins (P0.09 and P0.10).we want to set these two pins as uart function ,but...
Hi everyone,
I m nRF52 beginner and trying to understand that functions.
I have the few of qustions about DFU.
1. Is it that the mean of DFU equels "OTA DFU" referred...
I'm looking for a way to reliably determine (from the applications viewpoint) if a notification was successfully transmitted. Currently, we're having some issues when the...
Hello,
I am new to nrF52 480 chip. I am working on SDK15.3.0_59ac345's beacon code but have no result in the attempt to add device name to the existing beacon example. ...
Hey guys. I was working on a PCA10059 dongle. Now, I need to select suitable NRF52840 module. I know that there are some changes required in the code when I use module like...
Good morning,
In order to save some user data in flash, I want to fix page size to 32 bytes. It will be more useful for me, and it will be easier according to my project...
I've been playing around with the UART drivers on SDK 15.2. No issues with the Legacy (w/DMA) however I've tried switching over the NRFX_UARTE driver and I can't get the driver...
Hi,
Our device is based on nRF52840 SDK 15.0.0
The device verifies signature of incoming messages (which were sent over BLE from PC application) using ECDSA with spec256r1...
Hey guys. I am making a firmware using nrf52840 dongle which scans nearby bluetooth devices. I do not want to connect to any device, just send scanning data to another device...
Hi Because I have a custom board with the nRF91 module, there is no possibility to send data to nRF cloud, because it works only with DK boards. I would like to send asset...
I want to use this sample application, to connect with nRF52832 DK loaded with Running Speed and Cadence Application. In other words I want to use nRF9160 as a gateway for...
Hello all,
my compiler can't find the definition to timer functions : nrf_drv_timer_init(), nrf_drv_timer_extended_compare() and nrf_drv_timer_enable(). bellow my code :...
I am using Nordic nRF52832 Development kit . I want to interface Load Cell with the Development kit. Which examples in SDK i should refer to get started with Load Measurement...
