Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
Hi. I just recently started using nRF24L01+. I am trying to simulate MultiCeiver using 2 mcus and 2 nrfs.
PTX sends a message on all 6 pipes of the PRX. The problems start...
HI,
I look at nRF5 SDK doc about Gazell,see that 'the nrf_gzll_device_tx_info_t contains the num_channel_switches parameter which can be used by application to determine...
Hello
I am quite a beginner and have been trying to get it work for 2 weeks now.
I would like to merge these 2 example codes from nordic:
Shockburst TX example...
Hi everyone,
I want to use MasterEmulator.dll (2.1.13.14) in my own application (C#) for development. Then I realised that line
MasterEmulator mMasterEmulator = new...
I am using nRF52 and Raspberry Pi 3 (with BLE).
In the Raspberry Pi, I am using bluez.
I was attempting to connect with the NORDIC_BLINKY app but the message below was...
Hi, I wonder how to get the Nordic SDK-examples work with VisualGDB.
As I would like to read TWI sensor values a good point to start from are the Nordic examples.
But...
my project is used nrf51822 mcu, it contains SIM, when the mcu is reading SIM data, and at the same, I take out theSIM, and the 51822's pin which is link with SIM is can't...
Hi, Nordic
I use SDK12.1 with nRF52832, I found one issue:
if I do not program bootloader, nRFgo Studio can program app.
First, erase all flash, then program softdevice...
Hi Everone/Nodiac
I had tried so many threads and previous questions but not bale to get my answer so asking after two weeks.
I am willing to send a string from stm32f4...
Hello,
I currently working with the nRF52832 chip on a custom board. The external clock is a 32MHz clock with +/- 10 ppm. When I use nrf_delay_us or nrf_delay_ms the delay...
Hi all,
I am using a C# application with the masteremulator dll to connect to a nRF51822 with S110 V8.0.0
I can bond with a new device, and communicate with it in a...
In developing the device, for very low battery consumption, I encountered a feature of the implementation Gazell (ESB) protocol.
When I send a packet from the DEVICE (PTX...
Hello,
I am a little bit confused when reading in NRF52 spec that a NVM page is 4KB while block size is 512B. Usually an NVM memory is composed of block made of pages,...
Hi,
I am testing github.com/.../nRF52-fds-example
I am on nrf52832 with sdk 12.2.0 .
I can't seem to make it work.
What i have done:
Separated FDS stuff to separate...
Hi all,
I am trying use the SAADC in blocking mode inside a RTC I am currently using
The issues comes from the example
saadc_blocking_simple
the ADC always give...
