I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hello im trying to connect to a slave on BLE_GAP_EVT_DISCONNECTED event.
Can i use sd_ble_gap_connect(...) on this state, im getting error code 0x3202.?
regards, Vo...
Hi, I have bought the nRF51 development kit. I have downloaded source code for nRF51822. This comes with LOTS of examples but I suspect the codes are not for my board. Is...
I'm manually creating the .dat file for a DFU following the format specified in this document .
Where can I get the device type and revision values from to populate those...
I have bought the nRF51 dev kit. I can download all these soft devices. But what do they really correspond to ?
I think of them as library/apis for doing BLE development...
Hi,
I am trying to run the ble_app_hrs on my nrf51822 based board in combination with the nRF51822 Development Dongle. I am following the instructions from nRF51822 Development...
How can I add PKT_TYPE_INIT (DFU Contorl Point - OpCode = 2) into my DFU?
S110 nrf51_sdk_v6_1_0_b2ec2e6
Chip nrf51822
Softdevice s110_nrf51822_7.0.0_softdevice.hex...
I have a nRF51822 chip sending me BLE UART data to my phone and it works fine with the app. No I want to send it to my PC and Read the data (and send commands) via PuTTY....
Hey guys, I'm looking for a printed antenna PCB file. I have already read the white paper and I think using a more complex antenna would save more space and increases the...
I'm using SDK 7.1, PCA10028 eval board, SD310 2.0.1, MCP 3.6.0.8331
MCP and iOS are generating a different event sequences for a long writes.
MCP: after the BLE_EVT_USER_MEM_REQUEST...
Hey, I noticed that most of the wearable ble devices (without keyboard and screen) on the market are using 'push to confirm connection' authentication, when you have to push...
Chip nrf51822
S110 nrf51_sdk_v6_1_0_b2ec2e6
Softdevice s110_nrf51822_7.0.0_softdevice.hex
I use "nrf51_sdk_v6_1_0_b2ec2e6\nrf51822\Board\pub\device_firmware_updates...
Hi,
I am trying to set up a custom service and I have it all setup and it works properly. The only problem is that it is advertising as a 16bit service. I am moving from...
Take into account an application on the nRF51822 and S110.
I have defined different custom services, so UUID is 128bit long.
When advertising:
Is it advisable to include...
What are the mechanics of using 'uuids_more_available'? Is this list transmitted as a part of advertising data, scan response data, or both? How does the host know that this...
