I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
Hi:
Pls help me!
I use ncs v2.6.1.
C:\ncs\v2.6.1\zephyr\include\zephyr\sys\util_internal.h
When I check #define Z_IS_EMPTY_ (...) No matter what I input, I can't get...
Hello Nordic team and community,
I’m exploring the possibility of creating a mobile application (potentially using Flutter or native frameworks) that would act as a Distributor...
Hi,
I'm facing a critical issue with our sensor's power setup and would really appreciate any insights or suggestions.
Our sensor is currently using a CR2477 battery,...
Hi guys,
simple question based on your experience: what is a realistic data rate between an Android device and an nrf52805 with S112 on board?
I tried a lot of tweaks...
Hi, in our project we use the nRF52832 and a external flash memory MX25L3206E connected on this pins:
Take note in this project we also use SPIM0 to manage an IMU and...
Hi, I just purchased new PPK2 kit from mouser.
But after trying to open it via nrf Dekstop app it gives and error
2024-11-19T11:57:53.845Z INFO Selecting device with the...
Hello, I am trying to achieve a few uA current in nrf9160 but with even all conf off and empty while loop or even without the while loop the controller is consuming 5mA which...
We are currently working on a project based on nrf52840 and using connect sdk v17.0.0.
It is currently in development phase but eventually we are planning to use nrf5340...
Using v2.8.0-rc2 as v2.7.0 doesn't support the SCRATCH partition.
I am not able to enable BOOT_ECDSA_TINYCRYPT (required for Image Encryption).
I suspect this is because...
Hello
Awhile back I profiled my battery using power up app @ 4C 25C and 45C for a battery between 2.75V and 4.2V battery model is attached in zip.
The profiles themselves...
Dear Nordic Team,
I am working on a project using the nRF7002DK and require guidance on implementing the following functionality:
Acquire data from a sensor using the...
Hi, We have an application where we need to predict drift between two nRF52833 systems in low power mode running from LFRC (low frequency RC oscillator). Section 5.4.4.4 of...
I am an embedded software engineer and have experience developing BLE devices with nRF5SDK, but this is my first time using Zephyr/NCS.
I am developing a USB dongle (nRF52840...
Hi,
I am developing a product based on the nRF9160 using the LwM2M client. I successfully have this working using PSK, but want to use X509.
I am calling lwm2m_security_set_certificate...
