[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
Hello,
We are evaluating SDK 17.0.2 USB MSC example.
If we connect the PCA10056 board to USB the Windows make System Volume Information folder,
so if we don't make safely...
Development environment SDK 15.3.0
I am working on overturning the saadc project based on ble_app_uart.
The input frequency is 50~2k Hz.
Terminal and debug monitor...
Hello I'd like to output two PWM alternately. Using the timer, PWM1 and PWM2 alternate outputs every 5 seconds. And I want to change duty cycle according to adc value.
...
hello,
i am using nrf52840 in our customised board and trying to interface it with GDEW0213Z16 2.13 inch display which uses spi communication i have added the necessary...
Hi,
Currently, nRF91 supports only one MIPI RFFE-controlled device. In our solution, we would like to have two MIPI devices - one pair of LTE switches as in Thingy:91 for...
Hi ,
Technical Environment details:
nRF Connect SDK
segger Embedded Studio
nRF5340 DK board
1. I have enabled immutable bootloader and MCUboot bootloader.
...
Hello,
Per the datasheet, VDD_GPIO must be applied after VDD has been applied. Is there a minimum or maximum time?
For example, can VDD_GPIO be turned on 1 second after...
Hi,
I am evaluating nRF5340 for using it in a smart lock product with high security. I had evaluated nRF52840 before this
and was impressed with the integration that the...
I started with the ncs-display-ble-example which worked fine. Next I took the LVGL lv_demo_widget, ran it in the simulator using visual studio 2019 where it ran fine. Then...
Hi everybody.
Now I trying to make BLE central device.
I'm using nrf52832.
SDK : 17.0.2
SoftDevice :S132 7.2.0
(I'm completely new at nrf52 product.)
In case of...
hello
I'm currently developing a system that requires a nrf5280 to transfer data to an android phone through ble.
I've based my application on the Object transfer service...
I am entering the saadc source code based on ble_app_uart.
devzone.nordicsemi.com/.../i-am-creating-a-saadc-project-based-on-the-ble_app_uart-project
The source code...
I am advertising services, characteristics and descriptors. All are seen by nRF Connect (for iOS) but in the log I see this:
[Callback] peripheral(periphal, didDiscoverDescriptorsFor...
Hi,
We are currently evaluating a project, that uses the nrf52840 with an SD card and is connected as a USB device. One of the uses is the MCU is writing data to the SD...
Dear all:
When the PC1001 board connected with other BLE devices, how i can voluntarily disconnect them?
it seems that the use of the sd_ble_gap_disconnect function has...
