if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
We're looking for a few (2-3) savvy OS X users who might be interested in trying out Xcode to natively develop code for the nRF51/52 BLE SDK's. This build method does NOT...
Hello,
i'm working with my own board with the SD V6.0 and nrf51822 chip id QFAAG0. Already works fine.
Now i switch to the new SD V8.0. The SD V8.0 is programming with...
Hi everyone,
I'm working on the nrf51822 chip and using S110 stack of SDK 6.1. Everything is fine for IPhone5s. The proximity example is running on the nrf51822 device...
Dear Nordicsemi,
we need automatic simple test of ble function of our products - scanning bluetooth devices in rage and reading RSSI of device with specific mac address...
Sorry to bring up a topic which seems to have been discussed already, but I don't see an answer to my specific questions.
The original design of my project was to have both...
Hi,
The known issues section of SDK v1.3.0 release note states that
"
nRF5340
FOTA with the SMP Server Sample does not work.
"
Is this fixed in version 1.3.1?
Good morning, I'm working with the nRF52 DK and a custom board that has the nRF52810.
I am using the SDK 15.0.0 and followed the tutorial described here:
https://devzone...
Do you think my nrf is original?
The person I bought says it's original.
Can you please check it?
Seller link: http://www.ebyte.com/en/product-view-news.aspx?id=113
Hi,
I have a custom board in which i am using nRF52840 with SDK version is 16.0.0.
I have tested app_uart library its working Ok and current consumption is 6 uA in deep...
Hello,
I'm developing a project which uses two threads. One configures UART and keeps on a while(1) loop. But once it receives a byte, an ISR pushes the incoming byte...
Hello
I am adding the mpu6050 library in the ble_app_template of SDK 14.2.
Use the ble_mpu6050_simple example here. https://github.com/Martinsbl/nrf5-mpu-examples
I...
Hi, I have a set up consing of an nrf52840, a Raspberry pi and a Linux workstation, which communicate over IPSP following the IPSP sample from Zephyr OS. The nrf52840 is a...
Hi everyone,
Looking the examples of SDK16, I noticed that every example has a hex folder with some .hex files inside . This applies for both peripheral and ble examples...
Hello,
I want flash NRF52840 using AM57xx sitara processor(running on linux) over SWD interface. Can you please provide steps for the same. Is there any other methods available...
Hello,
We are using nRF52840 with SDK 15.2.0, a bootloader and the SoftDevice. We are able to perform a DFU by downloading the .bin and .dat files of the new firmware in...
Hi,
Following the example https://infocenter.nordicsemi.com/topic/sdk_tz_v4.1.0/thread_example_dfu.html how can you connect a jlink debugger and step through the application...
I read here...
NRF52840_PS_v1.1.pdf Peripherals > UART (6.33.7)
“An ERROR event, in the form of a framing error, will be generated if a valid stop bit is not detected...
Hi,
is there an updated example for SDK 15 or 17 for the multiprotocol example which uses BLE and ESB via the timeslot concurrently and at the same time allows the normal...
