In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Hi all !
I'm struggling to get a frequency jumping protocol up and running and can't figure out how to handle the following situation (please refer to the attached "pseudo...
Let's have light-switch provisioner, server and client.
My question is, how to send a message from a client or a server to the provisioner? In order to send a message, client...
Hi,
As part of my project, I need to use the SD card drivers of the nRF5 SDK and the I2S driver. The issue I am having is the following:
If I use pin 31 as the SCK signal...
Hi
This is a heads up that in SDK15.2.0 and file nrf_esb.c you have the line
m_rx_fifo.p_payload[m_rx_fifo.entry_point]->rssi = NRF_RADIO->RSSISAMPLE;
it should actually...
Hi
My application uses NFC for various reasons, and I need, at runtime to load up to 4 textural NDEF records onto the Nordic NRF 52832's NFC hardware.
If I wanted a simple...
Hey there faced with the following problem:
I have two hardware setups:
1. Laird DEVK-654 (nrf52480) without external oscillator
2. Laird BL654 mounted to a carrier...
I added the Generic OnOff Model from the thingy52-mesh-provisioning-demo to the Light Switch Proxy Client example from the nRF5_SDK_for_Mesh and get a linker error for the...
Hi All, I am polishing the code that we have, working out minor bugs, etc, we use Nordic UART to exchange data between our device and smartphone or tablet, sometimes data...
What is the proper way to temporarily disable the softdevice? Currently I have the following
sd_ble_gap_adv_stop(); bool disabled_softdevice = false; if (nrf_sdh_is_enabled...
hi ,
We developed a BLE slave device with NRF52840.
Well, we are doing product certification, BQB CE FCC, etc now.
One of the items is the 2m rate test, and we want...
hi ,
We developed a BLE slave device with NRF52840.
Well, we are doing product certification, BQB CE FCC, etc now.
One of the items is the 2m rate test, and we want...
Hi nordic members,
I am using nrF51822 board. I want to inform you that i am getting error undefined symbol: __data_start__ at compile time in segger embedded studio for...
Hi Nordic,
For battery_level measurement on the SDK we are using a timer such that for every 5 seconds or 10 seconds if the timer expires then the saadc will be triggered...
Hi!
I use nRF Connect Bluetooth Low Energy application for scanning. There are not all BLE devices on the device list.
The device that is not displayed on the list send...
It is required to track/locate the position of a bluetooth mesh node. I found that RSSI value can be used to estimate the distance between receiver node and a target node...