Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi,
I am trying to modify the multilink central example to send string to other board (peripheral)
I already did the UART configuration and in my tests I saw that when...
Hi, I tried the above tools(nrfjprog) on the Raspberry Pi 3.
But, I saw the error shown below.
pi@raspberrypi:~$ ls | grep nRF5x
nRF5x-Command-Line-Tools_8_5_0_Linux...
We are trying to modify the nRF Beacon example app for iOS that Nordic provides. We are unable to get app to see the devices from the iBeacon kit when they can be seen from...
The manuals for the nRF51 and nRF52 list the maximum ESB radio channel number
as 100, but in the SDK the guard value in the set channel function is <= 125
(in both the...
I am about to start development on a project that will be using a pair of nRF52832's to make a low data rate connection between a PC (with a nRF52832 based dongle) and a device...
In the event that a Nordic soft device library call fails (as determined by APP_ERROR_CHECK() macro) and our application level app_error_fault_handler () function is called...
Hello,
Ported my FreeRTOS application on NRF52 from SDK 12.2.0 to SDK 13.0.0 .My application is using freertos apptimer for timestamping and waking up of device which was...
Hi,
I am trying to run a ble mesh example but I prefer to work using keil, because I already worked other examples using the SDK (12, 13 and 14) and PCA10040/PCA10056 nordic...
For a precision timer application I have an external temperature compensated RTC (DS3231) which produces a highly stable 32 kHz signal connected to pin 5
When I associate...
Hello,
I am rather new to BLE and the NRF5x.
I want to build the following application: a swim timing sytem. The system consists of master timer with a high precision...
Hey,
I have a few questions about dynamic multiprotocol BLE/Thread support.
1. Multiple BLE connections. If I have one connection and connection event length is set for...
I'm working on a bootloader using the /examples/iot/bootloader as an initial template. The image to flash is stored on SD card. I'm at the point where I am successful in writing...
Hello.
i setup - BLE Stack + Uart 1 + SPI 1.
Infinite loop inside nothing code.
nRF52832 consumed 5mA + a.
and i add power_manage() in Infinite loop.
Nevertheless...
Hi,
We are potentially considering using nRF52 DK in our projects. Kindly advise on following questions,
(Q) How we can use uC/OS-II or uC/OS-III with nRF52 or other nordicsemi...