I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
Hi all.
I have phone with nrf Tollbox and central device with DFU, SD130 2.0.0, SDK11.
I would like flash application to central by OTA when I enter password in nrfToolbox...
Hi Nordic,
EDIT: I am using nrf51422, with S210 v5.0.0. Everything that is below is referring to ANT protocol
I want to know if the thing that I am planning to do is...
I download the example of multilink central (S130) into nrf51822 .The central transmit 20 bytes to peripheral interval 50ms sometimes will reset.Anybody know the bluetooth...
Hi guys,
I have the NRF52-DK and want to power only the NRF52. So basically, I want to power it over VDD_nRF.
When I power my DK with a battery and then measure my current...
Hello!
Is it possible to read data sent from ble_app_hrs (peripheral ) to ble_app_uart_c (Central) on PC's serial monitor? If possible, how can i achieve this and which...
Hi,
I programmed nRF52 DK with BLE_APP_UART_SAADC_TIMER_DRIVEN with AIN6 pin as input and is working correctly. But when I programmed the same code in BMD300 the adc count...
I'm running an nrf52832, using SDK 11.0 and the S332 soft device. I've had instances where it seemed my flash data, stored with FDS, was corrupt after a firmware upgrade....
Hi Nordic,
I am having problems knowing what exactly happens in the following situation:
I have a connection established between a master and a slave, and the master...
Hi,
I have started your tutorials and just complement this one. devzone.nordicsemi.com/.../
Now when I tried to download other programs on the development kit, I get...
Hi,
I have wierd experience about using float32_t.
This is my test:
When i use operations on float64_t i got:
0.0001s MAIN:INFO:init_finished
0.0001s MAIN:INFO:loop...
I have a program which uses two timers to flash an LED, alternating between flashing once every 5s for 15s, then once every 0.25s for 15s.
If I run this on the nRF52-DK...
Hello,
I am new to nrf51822 BLE. I am using MDBT40 (nrf51822 series). Complete project is powered by 12V, 2500 Mah lithium ion Battery pack. I want to monitor battery level...
Hi,
I know how to OTA a ble device, but how do this on a ble master?
Is there any nrf tool can OTA a ble master ?
dev environment:
SoftDevices:S130 v2.0.1
sdk: nRF5_SDK_12...
Hi,
we are using a ISP130301 module from Insight SIP (containing a nrf51822CEAA ) with a low power acceleration sensor ADXL362 , connected via SPI. SoftDevice is s130_nrf51_2...
Hi,
SDK: nRF5_SDK_12.2.0_f012efa
No softdevice
Example: nRF5_SDK_12.2.0_f012efa\examples\peripheral\radio\transmitter\pca10040\blank
and receiver.
I have running...
